All MetalShaping

Go Back   All MetalShaping > GETTING STARTED > Introductions
Reload this Page Better late than never?
Register All Albums Event Calendar Today's Posts Search
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 09-27-2011, 08:08 PM
Aaron Franck Aaron Franck is offline
Member
  
Join Date: Dec 2009
Location: Anamosa, Iowa
Posts: 33
Default Better late than never?
Hello everyone,
I've been lurking for sometime now. Been very busy building a shop, things have slowed down just enough I think I can properly introduce myself. I've been a member on Metalmeet since 2003 and went to 2 or 3 Metalmeet's. I worked for years as a welder and fabricator and then tried opening my own Fab. shop. After 4 years I realized I'm not the businessman I hoped I was. Luckily, right place at the right time, I now drive truck for a pretty good living. I'm in the middle of a three? year project building my dream shop. 50 x 70 x 16.5
Feel free to check out my website at: http://www.aaronfab.com/


Aaron
Reply With Quote
  #2  
Old 09-27-2011, 08:14 PM
Kerry Pinkerton's Avatar
Kerry Pinkerton Kerry Pinkerton is offline
Administrator
  
Join Date: May 2009
Location: Near Huntsville, Alabama. Just south of the Tennessee line off I65
Posts: 8,490
Default
Hi Aaron, Good to hear from you again. Welcome to AllMetalShaping!
__________________
Kerry Pinkerton
Reply With Quote
  #3  
Old 09-27-2011, 08:17 PM
Joe Hartson's Avatar
Joe Hartson Joe Hartson is offline
Administrator
  
Join Date: May 2009
Location: Pass Christian, MS
Posts: 5,003
Default
Aaron, welcome and thanks for the introduction. Nice web site, looks like you do a little bit of everything. Hope to see you post more of your work here. Sounds like you are building a nice shop. Enjoy the site.
__________________
Joe Hartson

There is more than one way to go to town and they are all correct.
Reply With Quote
  #4  
Old 09-28-2011, 08:21 AM
bob baisden bob baisden is offline
Member
  
Join Date: May 2009
Posts: 134
Default
Hi Aaaron,

Do your thumbnail dies, still shrink faster than Clay Cooks? haha Is Norton around anymore?

Bob
Reply With Quote
  #5  
Old 09-28-2011, 08:26 AM
mr.c's Avatar
mr.c mr.c is offline
Member
  
Join Date: May 2009
Location: N. Florida
Posts: 698
Default
Hi Aaron. Welcome to AllMetalShaping. It is good to hear from you.
__________________
Carey Culpepper

TuckPuck® Metal Shaping Tools
www.tuckpuck.com
Reply With Quote
  #6  
Old 09-28-2011, 09:48 AM
HEATNBEAT's Avatar
HEATNBEAT HEATNBEAT is offline
Member
  
Join Date: May 2009
Location: Madera,Ca. Home of Yosemite
Posts: 6,058
Default
Welcome Aaron!
__________________
Rick Scott
The second mouse gets the cheese!
Reply With Quote
  #7  
Old 09-28-2011, 01:39 PM
Ben's Avatar
Ben Ben is offline
MetalShaper of the Month Dec 2010, Sept 2015, Jan 2016
  
Join Date: May 2010
Location: The Netherlands
Posts: 645
Default
Hi Aaron,

long time no see , remember me

Nice website...welcome to the site.

Ben
__________________
Ben
www.mechammer.com
Reply With Quote
  #8  
Old 09-28-2011, 07:42 PM
Aaron Franck Aaron Franck is offline
Member
  
Join Date: Dec 2009
Location: Anamosa, Iowa
Posts: 33
Default
Kerry, nice website, and sweet car!

Bob, yes they do and I haven't heard from John for a long time.

Ben, of course I remember you, like checking out your site from time to time. Awesome work always.

Good to hear from all of you. Hope to post, time allowing.



Aaron
Reply With Quote
  #9  
Old 09-28-2011, 09:09 PM
tdoty's Avatar
tdoty tdoty is offline
Administrator
  
Join Date: May 2009
Location: Winchester, TN
Posts: 1,327
Default
Welcome aboard, Aaron! Long time no see!
__________________
Tim D.
Reply With Quote
  #10  
Old 09-28-2011, 09:29 PM
Peter Tommasini Peter Tommasini is offline
MetalShaper of the Month May 2013, Dec 2013
  
Join Date: Apr 2011
Location: Melbourne,Victoria, Australia
Posts: 7,764
Default
Welcome to the site Aaron you have some cool projects on your website.
__________________
P.Tommasini

Metalshaping tools and dvds
www.handbuilt.net.au

Metalshaping clip on youtube
http://www.youtube.com/watch?v=WEAh91hodPg

Making Monaro Quarter panel:
http://www.youtube.com/watch?v=KIpOhz0uGRM
Reply With Quote
Reply

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -5. The time now is 10:26 AM.
Back to the Top
Contact Us - allmetalshaping.com -

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.