All MetalShaping

Go Back   All MetalShaping > General Metal Shaping Discussion > Basic questions and answers
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-14-2022, 05:42 PM
TeHoro TeHoro is offline
Member
 
Join Date: Feb 2012
Location: New Zealand
Posts: 6
Default What does this machine do?

I picked this up from a shop that used to do sheetmetal work, along with some bead rollers and a Pullmax P13.

It's some form of edge 'crimping' machine I suppose. Can anyone describe it's purpose better than that?

I haven't powered it up yet, but it looks fairly simple. I expect it would put waves in a tipped edge/flange, but I'm not sure why the working part isn't flust with the machine table.

P1080338.jpg

P1080339.jpg

P1080340.jpg
__________________
NZ (Occasional) Metalshaper - Trevor

Last edited by TeHoro; 06-14-2022 at 05:45 PM.
Reply With Quote
  #2  
Old 06-14-2022, 06:56 PM
Precocious Jeremiah Precocious Jeremiah is offline
Member
 
Join Date: Mar 2017
Location: Adelaide hills, South Australia
Posts: 41
Default

G'day Trevor, I think you are on the money. Looks suspiciously like a machine I saw a few decades ago for crimping the end of wood stove flue sections.
I hope you are not too cold across the ditch to get out in the shed.
cheers C J
__________________
Cheers Christopha
Reply With Quote
  #3  
Old 06-14-2022, 10:50 PM
TeHoro TeHoro is offline
Member
 
Join Date: Feb 2012
Location: New Zealand
Posts: 6
Default

I have a heater for when it gets too chilly.
__________________
NZ (Occasional) Metalshaper - Trevor
Reply With Quote
  #4  
Old 06-15-2022, 01:52 PM
Gareth Davies Gareth Davies is offline
Member
 
Join Date: Aug 2012
Location: Staffordshire, England
Posts: 661
Default

It looks like itís a Shorte, or Oliver, power flanger. The serrations on the wheels are more for grip than creating crimps. I had one similar a few years ago but sold it as it seemed to have limited uses to me. They run at constant speed, which is fairly quick, so you have to pay attention whilst feeding the workpiece through. You can also only create a relatively small flange on the workpiece so that was a limiting factor. Finally, those serrations can chew the job up and make it look nasty.

If it didnít cost you a lot, and you have the space to keep it, hang on to it as you might get some use out of it. If not, Iíd sell it and use the money to buy tools that you will use.

If it is one of the makes I've named, on the front right corner of the top plate thereís a small piece fixed to the underneath with a small gap. This allows you to pre-bend the workpiece to allow you to feed it into the rollers.

Hope that helps.
__________________
Gareth Davies
Reply With Quote
  #5  
Old 06-15-2022, 05:32 PM
Jaroslav Jaroslav is offline
MetalShaper of the Month April 2020, September 2021
 
Join Date: Dec 2012
Location: Czech Republic
Posts: 1,937
Default

https://www.youtube.com/watch?v=z-36gcNcHLg
__________________
Jaroslav
Reply With Quote
  #6  
Old 06-16-2022, 03:26 PM
TeHoro TeHoro is offline
Member
 
Join Date: Feb 2012
Location: New Zealand
Posts: 6
Default

Quote:
Originally Posted by Gareth Davies View Post
It looks like itís a Shorte, or Oliver, power flanger. The serrations on the wheels are more for grip than creating crimps. I had one similar a few years ago but sold it as it seemed to have limited uses to me. They run at constant speed, which is fairly quick, so you have to pay attention whilst feeding the workpiece through. You can also only create a relatively small flange on the workpiece so that was a limiting factor. Finally, those serrations can chew the job up and make it look nasty.

If it didnít cost you a lot, and you have the space to keep it, hang on to it as you might get some use out of it. If not, Iíd sell it and use the money to buy tools that you will use.

If it is one of the makes I've named, on the front right corner of the top plate thereís a small piece fixed to the underneath with a small gap. This allows you to pre-bend the workpiece to allow you to feed it into the rollers.

Hope that helps.
Thanks All

Has a Shorte engineering label on it. I don't see a slot for starting the bend.

I'll power it up an some point and see how it goes, but probably won't keep it long term as it takes up a fair bit of space. I didn't pay much for it, came with a larger log of bead rollers.
__________________
NZ (Occasional) Metalshaper - Trevor
Reply With Quote
  #7  
Old 06-16-2022, 04:24 PM
Jaroslav Jaroslav is offline
MetalShaper of the Month April 2020, September 2021
 
Join Date: Dec 2012
Location: Czech Republic
Posts: 1,937
Default

Trevor, I can't use it based on a precisely drawn line or distance from the edge. I can't do it exactly where I need it. In bead roller, I'm slow but accurate.
It's great for piping and productivity is great. I'll probably sell it.
__________________
Jaroslav
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

All times are GMT -5. The time now is 11:13 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.