All MetalShaping

Go Back   All MetalShaping > General Metal Shaping Discussion > General Discussion
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 11-06-2020, 11:41 AM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default Battle of Britain Spitfire Homage

Hi folks - it’s been a while... hope you are all ok in these strange times!

I was recently commissioned by a customer to create a kinetic Spitfire sculpture for his father’s 60th birthday. He’d seen a similar sculpture created by Richard Cresswell here in the UK. Anyway, I took a look at the project and decided I could create something similar, albeit “only” six and a half feet tall!

I’ll post all of the build pictures on here and discuss how I made it, what I learned from it and highlight one or two “mistakes” I made and how I ratified them.

Metal shaping is all about learning. I’m 53 now, and make more then my fair share of mistakes, but luckily have just enough experience to dig myself out of the hole I dug! Sometimes it’s best to put the hammer down, put the kettle on and think, think think. The solution will normally present itself, but... only after a breather to regain all rationality!

Anyway, let me start. The customer presented me with a beautiful Spitfire model, which I could use for scaling and measurements.

__________________
Matt Keene
www.air-Kraft.com
Reply With Quote
  #2  
Old 11-06-2020, 11:44 AM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

So, in the first image I’m playing with the fuselage shape. The Spit needs to look like it’s at speed in a fully banked turn. I’ve taken the dimensions from the model and transferred the data on to sheet steel. To help draw the outline, I’m using magnets and bendy thin wood...
__________________
Matt Keene
www.air-Kraft.com
Reply With Quote
  #3  
Old 11-06-2020, 11:50 AM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

The outline is then transferred onto 0.080” aluminium, taking into account the dimensions required to make the fuselage from two halves:

__________________
Matt Keene
www.air-Kraft.com

Last edited by Stretch; 11-06-2020 at 02:12 PM.
Reply With Quote
  #4  
Old 11-06-2020, 11:55 AM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

I then cut out three blanks from 0.080” aluminium: two for the fuselage halves a third to create a central reinforcement plate, to give rigidity to the structure:

upload images
__________________
Matt Keene
www.air-Kraft.com
Reply With Quote
  #5  
Old 11-06-2020, 11:56 AM
Gareth Davies Gareth Davies is offline
Member
 
Join Date: Aug 2012
Location: Staffordshire, England
Posts: 665
Default

Subscribed. Will be interesting to see how this progresses.
__________________
Gareth Davies
Reply With Quote
  #6  
Old 11-06-2020, 12:10 PM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

The two halves of the fuselage are placed flat together and then seam welded all of the way around. I then fully anneal both sides of the flat form. I’m using a technique I played with a while back, which for want of any better description I’m going to call pressure annealing.

A simple piece of tube - the diameter of my compressed air blow gun - is then welded to the outside edge. This will allow compressed air to blow in the centre - similar to hydroforming. Then... compressed air is blown into the two halves and - voila - the shape of the fuselage takes form. Now, and here’s the slight tricky part that’s not without some pitfallls... I use the oxy-acetylene to anneal where I want the shape to form whilst on the fly. Essentially, I’m keeping the structure under pressure with air at shop pressure (under 100 psi - yep, that low), and coax the shape to form with judicious annealing.

__________________
Matt Keene
www.air-Kraft.com

Last edited by Stretch; 11-06-2020 at 12:48 PM.
Reply With Quote
  #7  
Old 11-06-2020, 12:15 PM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

As you can see, a lot of the shape is already created and it’s a relatively simple process. Yes, it’s a long way from a finished article, but 80% is there and the beauty is you have two identical halves!



__________________
Matt Keene
www.air-Kraft.com
Reply With Quote
  #8  
Old 11-06-2020, 12:22 PM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

The two halves are then bandsawed apart, the welds filed off and it’s time to smooth out and refine the shape. The weapon of choice here is my trusty air planisher. I’m using an acetal upper hammer in a homemade tool. This is to avoid damage marks to the aluminium.



__________________
Matt Keene
www.air-Kraft.com
Reply With Quote
  #9  
Old 11-06-2020, 12:58 PM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

The nose was a tricky section. The pressure forming came up short here, mostly due to the extreme amount of shape. A little traditional beating was definitely necessary...

__________________
Matt Keene
www.air-Kraft.com
Reply With Quote
  #10  
Old 11-06-2020, 01:01 PM
Stretch Stretch is offline
MetalShaper of the Month Aug 2016, Feb 2017, Sept 2018, Dec 2020, Aug 2022
 
Join Date: Dec 2014
Location: Cornwall, England
Posts: 550
Default

Time to get medieval on its ass! A bit of old school stump shrinking and shaping. Obviously both sides (halves) need to match...

__________________
Matt Keene
www.air-Kraft.com
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 03:57 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.