Now introducing: An unexperienced onlooker...

[austinhunt]

Hello,
I'm Austin Hunt as the handle suggests and I have no experience forming. I live in Fairbanks Alaska and dont do much aside from earning and engineering degree and working on my Graham Brothers Truck.

I would like to pick up some knowledge to help metal finish my dented panels and form some rear fenders.

I have no tools and cant afford a wheel or bead roller. So any info on hand-made hand-tools or input on what is essential to those with experience would be interesting. I recently bought a dvd from David (metalshapingzone.com) and intend to study up.

Unfortunately I will be moslty a silent onlooker or question-asker for a while until I get something under my belt.

[Joe Hartson]

Austin, welcome and thanks for the introduction. Hope you enjoy the site and find it helpful. Lots of good information here if you read a lot of the threads. Thanks for joining us.

[austinhunt]

Thanks! Any suggestions to favorite threads are appreciated also.

[weldtoride]

Originally Posted by austinhunt

Thanks! Any suggestions to favorite threads are appreciated also.

Welcome to the forum and to the craft.

Have you looked carefully thru the index?

http://allmetalshaping.com/index.php

I would suggest: Basic Questions and Answers, and Basic Tools as starting points. Any thread with a Sticky bears extra attention as well.

This thread: http://allmetalshaping.com/showthread.php?t=1706 proves you don't need a lot of sophisticated tools to get started.

The link below was posted recently in the above thread and is noted for its clarity in getting a concept across. I might add that watching the other videos by the same youtube poster is worthwhile.

https://www.youtube.com/watch?featur...&v=tQCS3KCpNJY

You have a most excellent tool already in David's video. His "stump" also proves you don't need as large a chunk of tree as many think.


As far as removing fender dents goes, an oversimplification of collision repair, but a basic rule of thumb is: "Last in, first out". That often but not always, means start on the outer edges and work your way into the initial strike area.

A few clicks away and you can start reading some basics on page 30 (and following) in this old manual, great illustrations of on-dolly work vs. off-dolly, and of sequencing your actions:

http://www.hnsa.org/doc/pdf/metal-body-repair.pdf


If you want to spend a couple dollars, get Frank Sargent's metal bumping book, there's a reason it's been in print since 1953:

http://www.amazon.com/Bumping-Instru...+metal+bumping


Hope this helps,

Mark

[austinhunt]

Peter Tommasini - Well... it was -15 F (-26 C) yesterday and by Christmas it will be -40 F (-40 C also) or worse at least a couple times a month. last year it was -30 for an entire month! Working in it is terrible but living isn't that bad.

HEATNBEAT - Thank you.

Weldtoride - Thanks, I will look into that. The very first place I visited was the basic tools section. Got some great ideas and loved the idea of using river rock as a dolly. Also the leaf spring slappers are on my list.

Thanks for all the basic info. The little things are often never stated.

I will spend the evening reading and watching.

[austinhunt]

This is my first attempt. I used a pair of needle nose pliers as a puckering iron, and a framing hammer to shrink the edges. Ugly, but it's to be expected from hammer that has seen better days and a toy anvil.

[Peter Tommasini]

[QUOTE=austinhunt;62020]Peter Tommasini - Well... it was -15 F (-26 C) yesterday and by Christmas it will be -40 F (-40 C also) or worse at least a couple times a month. last year it was -30 for an entire month! Working in it is terrible but living isn't that bad.

Gee that's cold I will never complain about the Australian weather again.
I can not immagine picking up up a doly in that temperature my hand would freze
Peter

[Peter Tommasini]

HI Austin welcome to the forum
Peter
PS how cold will it get in winter in Alaska
reason for asking is because we always complain that it's to cold to work here in Australia maybe I am getting to old

[HEATNBEAT]

Hi Austin and welcome!