Forum: Individual Classifieds
02-22-2024, 08:57 AM
|
Replies: 3
Views: 532
Irontrapfinds on Instagram is selling a...
Irontrapfinds on Instagram is selling a planishing hammer with interchangeable hoops right now
https://www.instagram.com/p/C3ld9VOvvE-/?img_index=1
but its $800 US plus shipping and its the small...
|
Forum: Automotive Projects
01-13-2024, 04:29 PM
|
Replies: 40
Views: 57,059
|
Forum: Automotive Projects
01-10-2024, 11:48 AM
|
Replies: 40
Views: 57,059
|
Forum: Automotive Projects
01-09-2024, 05:40 PM
|
Replies: 40
Views: 57,059
|
Forum: Automotive Projects
01-09-2024, 05:37 PM
|
Replies: 40
Views: 57,059
|
Forum: Automotive Projects
01-09-2024, 05:36 PM
|
Replies: 40
Views: 57,059
|
Forum: Automotive Projects
01-09-2024, 05:30 PM
|
Replies: 40
Views: 57,059
Then patches were made. I made strips slightly...
Then patches were made. I made strips slightly wider than the holes, ran them through the english wheel with a low crown lower. Broke the ends to math up, hand planished them as well as the edges of...
|
Forum: Automotive Projects
01-09-2024, 05:26 PM
|
Replies: 40
Views: 57,059
|
Forum: Automotive Projects
01-09-2024, 05:21 PM
|
Replies: 40
Views: 57,059
Before I got too far I wanted to make sure I...
Before I got too far I wanted to make sure I could make the trunk fit before making the catwalk filler panels. I broke some 16 gauge to 90 and ran the edge in the planishing hammer with a linear...
|
Forum: Automotive Projects
01-09-2024, 05:17 PM
|
Replies: 40
Views: 57,059
Been awhile friends! Time to knock the dust off...
Been awhile friends! Time to knock the dust off and give some updates!
So when the car is widened and there is a Vee shape, that Vee shape must also move out so that it stays in alignment. Following...
|
Forum: Automotive Projects
11-19-2023, 01:09 PM
|
Replies: 19
Views: 261,121
|
Forum: General Discussion
11-19-2023, 08:43 AM
|
Replies: 13
Views: 2,472
|
Forum: General Discussion
11-18-2023, 08:58 AM
|
Replies: 13
Views: 2,472
Thank you everyone for the advises! I like the...
Thank you everyone for the advises! I like the idea of getting plates laser cut and making male and female dies!
here is the logo rendering I did, it still needs some refinement. but I like where...
|
Forum: General Discussion
11-15-2023, 06:59 PM
|
Replies: 13
Views: 2,472
die stamping
I am throwing around the idea of die stamping a custom logo into sheet metal and welding it into a steel valve cover. I know a lot of people go the route of having logos laser etched or cnc milled,...
|
Forum: Automotive Projects
10-17-2023, 05:13 PM
|
Replies: 13
Views: 5,238
|
Forum: Automotive Projects
01-21-2022, 08:34 PM
|
Replies: 2,245
Views: 4,174,297
|
Forum: Automotive Projects
01-21-2022, 07:30 PM
|
Replies: 40
Views: 57,059
I was finally able to cut the body after...
I was finally able to cut the body after measuring and measuring and measuring. I am starting to try and support the roof sections with 16 gauge angles to the proper shape. I ran these through the...
|
Forum: Automotive Projects
01-21-2022, 07:22 PM
|
Replies: 40
Views: 57,059
|
Forum: Introductions
11-22-2021, 10:17 AM
|
Replies: 6
Views: 1,865
|
Forum: Automotive Projects
11-12-2021, 11:26 AM
|
Replies: 40
Views: 57,059
|
Forum: Metalshaping videos on-line
11-12-2021, 11:22 AM
|
Replies: 0
Views: 9,397
My attempt at a motorcycle tank repair
Hello everyone! My friend brought me a motorcycle tank for a restoration on his 1970 Yamaha XS 650. While this tank did not look too bad at first, we uncovered some bad bad things on it. I added a...
|
Forum: Shop Safety
09-12-2021, 12:46 PM
|
Replies: 14
Views: 21,146
|
Forum: Automotive Projects
09-10-2021, 10:59 AM
|
Replies: 40
Views: 57,059
|
Forum: Automotive Projects
09-09-2021, 04:57 PM
|
Replies: 461
Views: 246,089
|
Forum: Automotive Projects
09-09-2021, 06:39 AM
|
Replies: 530
Views: 509,977
|