Forum: Welding Sheet Metal
03-01-2021, 09:58 AM
|
Replies: 1
Views: 118
Either .023-.025 or .030, ER70S6. ER70S6 is...
Either .023-.025 or .030, ER70S6. ER70S6 is pretty much standard now. If you are welding perfectly clean material ER70S2 works well. Some Mig's like the thinner wire, some do better with .030. Just...
|
Forum: Automotive Projects
01-09-2021, 05:03 PM
|
Replies: 360
Views: 105,748
|
Forum: Basic questions and answers
01-06-2021, 01:23 AM
|
Replies: 5
Views: 369
After reading your post again, before you do...
After reading your post again, before you do anything else put more shape into the bottom half of the panel. If it fits when you hold it up, but then does not when you drop it down the panel is...
|
Forum: Basic questions and answers
01-06-2021, 01:13 AM
|
Replies: 5
Views: 369
This is what I would try. Hope this translates...
This is what I would try. Hope this translates from my brain to words...:)Take some small rod 3/16 or 1/4 something that bends easily and span the gap between the fenders. Shape it so that you have...
|
Forum: Buck Building
12-20-2020, 12:33 PM
|
Replies: 11
Views: 848
JMO, but this is one of those questions that...
JMO, but this is one of those questions that there is no step one, step two step three etc, easy answers to. You just have to do a lot of searching and reading and learning, along with trial and...
|
Forum: Welding Sheet Metal
12-18-2020, 12:17 PM
|
Replies: 8
Views: 748
What about a heli-coil insert? If I understand...
What about a heli-coil insert? If I understand your circumstances that would seem to be the easiest solution if you haven't removed too much material. Inserts require you to drill oversize anyways or...
|
Forum: Basic questions and answers
12-14-2020, 05:52 PM
|
Replies: 14
Views: 946
Side by side comparison of (L-R) Snap-On BF618...
Side by side comparison of (L-R) Snap-On BF618 with the original handle, Dagger Tools replacement handle, and my nicest original Proto I have, a 1427.(I'm not a tool collector, but I don't use it...
|
Forum: Basic questions and answers
12-08-2020, 06:39 PM
|
Replies: 13
Views: 981
|
Forum: Basic questions and answers
12-07-2020, 12:10 PM
|
Replies: 14
Views: 946
|
Forum: Automotive Projects
12-01-2020, 11:21 PM
|
Replies: 252
Views: 100,033
|
Forum: Basic questions and answers
11-10-2020, 05:58 PM
|
Replies: 10
Views: 1,094
|
Forum: Basic questions and answers
10-08-2020, 11:59 AM
|
Replies: 5
Views: 601
.041 sounds like .040 sheet, while the .049...
.041 sounds like .040 sheet, while the .049 sounds like .050 sheet. To me it seems as if you were mistakenly sold .040 sheet instead of .050. There is quite a bit of difference strength wise...
|
Forum: Heads Up Announcements
09-19-2020, 07:17 PM
|
Replies: 8
Views: 1,277
|
Forum: General Discussion
09-17-2020, 12:45 PM
|
Replies: 42
Views: 16,843
|
Forum: General Discussion
09-15-2020, 10:26 PM
|
Replies: 42
Views: 16,843
|
Forum: Introductions
09-05-2020, 09:53 AM
|
Replies: 4
Views: 639
|
Forum: Automotive Projects
09-03-2020, 12:28 PM
|
Replies: 25
Views: 5,971
|
Forum: Automotive Projects
09-01-2020, 11:29 AM
|
Replies: 1,734
Views: 608,086
|
Forum: Basic questions and answers
08-31-2020, 09:36 PM
|
Replies: 27
Views: 6,827
Technique you are describing is called pumping....
Technique you are describing is called pumping. It has it's place but again you are not going to wheel and shrink alone a panel like he is trying to make. Wheeling alone (or combined with shrinking)...
|
Forum: Basic questions and answers
08-31-2020, 05:53 PM
|
Replies: 27
Views: 6,827
|
Forum: Announcements
08-25-2020, 05:48 PM
|
Replies: 23
Views: 7,175
|
Forum: Buck Building
07-22-2020, 03:37 PM
|
Replies: 16
Views: 4,046
|
Forum: Basic questions and answers
07-21-2020, 09:50 AM
|
Replies: 30
Views: 6,058
|
Forum: Automotive Projects
07-17-2020, 01:16 PM
|
Replies: 16
Views: 2,735
|
Forum: General Discussion
07-07-2020, 12:40 PM
|
Replies: 57
Views: 13,374
|