Copper project just completed....

Copper project just completed....

  • Reaction score 0
  • Comments 0
Here is a close up of the copper heart-cross project we are donating to a local charity for a silent auction

Here is a close up of the copper heart-cross project we are donating to a local charity for a silent auction

  • Reaction score 0
  • Comments 0
Two safety blades welded on edge.......I love Miller welders...

Two safety blades welded on edge.......I love Miller welders...

  • Reaction score 0
  • Comments 0
Here is what the Kennedy High School Chopper project looks like at this point.......This will be one cool scoot

Here is what the Kennedy High School Chopper project looks like at this point.......This will be one cool scoot

  • Reaction score 0
  • Comments 0
Kennedy High School Chopper class students made the tank wood buck....

Kennedy High School Chopper class students made the tank wood buck....

  • Reaction score 0
  • Comments 0
Kennedy High School chopper class project gas tank we are making for the students.

Kennedy High School chopper class project gas tank we are making for the students.

  • Reaction score 0
  • Comments 0
That is a weld bead no wider than the width of a penny.....

That is a weld bead no wider than the width of a penny.....

  • Reaction score 0
  • Comments 0
We hid the alternator below the motor. I never liked the alternator sticking out the side. The water pump will be driven off the bottom blower pulley.

We hid the alternator below the motor. I never liked the alternator sticking out the side. The water pump will be driven off the bottom blower pulley.

  • Reaction score 0
  • Comments 0
About 75% done. Now we can put the weight of the motor on the springs to see how much we need to lower the motor.

About 75% done. Now we can put the weight of the motor on the springs to see how much we need to lower the motor.

  • Reaction score 0
  • Comments 0
A little trimming here and there

A little trimming here and there

  • Reaction score 0
  • Comments 0
Start of the engine plate. Now to cut away the un needed parts.

Start of the engine plate. Now to cut away the un needed parts.

  • Reaction score 0
  • Comments 0
This is close to the final engine position. Now we can make the front engine plate which will include a mounting provision for the mopar alternator un

This is close to the final engine position. Now we can make the front engine plate which will include a mounting provision for the mopar alternator un

  • Reaction score 0
  • Comments 0
Now we can move things to where the look right and then tack them in place. Next up is to fab the rear end (narrow it) and then it is a roller. These

Now we can move things to where the look right and then tack them in place. Next up is to fab the rear end (narrow it) and then it is a roller. These

  • Reaction score 0
  • Comments 0
Front leafs tacked into place.

Front leafs tacked into place.

  • Reaction score 0
  • Comments 0
1932 Ford frame boxed (tacked at this point). Will finish the boxing once the cage is installed. This will keep the warping down to a minimum

1932 Ford frame boxed (tacked at this point). Will finish the boxing once the cage is installed. This will keep the warping down to a minimum

  • Reaction score 0
  • Comments 0
This open section will get boxed tomorrow for some stiffness and strength. Open frame is ok for a street rod, but not for a dragster.

This open section will get boxed tomorrow for some stiffness and strength. Open frame is ok for a street rod, but not for a dragster.

  • Reaction score 0
  • Comments 0
32 Ford reproduction rails

32 Ford reproduction rails

  • Reaction score 0
  • Comments 0
Radiator mount in the 1970 nova installed.

Radiator mount in the 1970 nova installed.

  • Reaction score 0
  • Comments 0
3[1]

3[1]

  • Reaction score 0
  • Comments 1
6[1]

6[1]

  • Reaction score 0
  • Comments 1
5[1]

5[1]

  • Reaction score 0
  • Comments 1
2[1]

2[1]

  • Reaction score 0
  • Comments 1
not much metal shaping here. Made this air catcher out of four pieces. Botton, two side and top. The sides had the upper edge hammerformed. The top is

not much metal shaping here. Made this air catcher out of four pieces. Botton, two side and top. The sides had the upper edge hammerformed. The top is

  • Reaction score 0
  • Comments 0
This is not a vehicle that will blend into the crowd...... I am shooting for a gasser built in 1961, the year I was born. Should be a roller be the en

This is not a vehicle that will blend into the crowd...... I am shooting for a gasser built in 1961, the year I was born. Should be a roller be the en

  • Reaction score 0
  • Comments 0
D

Pics from the shop

Some pictures from stuff going on in the shop
Click to expand...

Album information

Album owner
denniswolf2001
Date created
Item count
43
View count
13
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

D

denniswolf2001

Media items
43
Albums
1
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top