All MetalShaping

Go Back   All MetalShaping > Metal Shaping Projects > Automotive Projects
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Reply
 
Thread Tools Search this Thread Display Modes
  #11  
Old 08-14-2020, 04:27 AM
Antoine_P Antoine_P is offline
MetalShaper of the Month August 2020
 
Join Date: Feb 2019
Location: Stuttgart, Germany
Posts: 113
Default

That does look great! Taking time to weld is the key to avoid too much distortion 👍

Antoine
__________________
Antoine Puygranier
Resurrecting a 60 ghia:
http://www.allmetalshaping.com/showthread.php?t=18852
Reply With Quote
  #12  
Old 09-01-2020, 10:07 PM
Reno Reno is offline
MetalShaper of the Month May 2020
 
Join Date: Nov 2018
Location: Reno, NV
Posts: 141
Default

Since the door is longer it gets thinner so a section was taken out.

Name:  IMG_20200816_172145.jpg
Views: 635
Size:  55.8 KB

Name:  IMG_20200816_172154.jpg
Views: 636
Size:  47.7 KB

Then the infill 7" piece fitted between the original skins.

Name:  IMG_20200829_150516.jpg
Views: 564
Size:  50.1 KB

I thought I was butt welding at an area without much shape, but spent a lot of time with hammer and dolly and the shrinking disc to get to here. I failed to give myself decent access to the inside for the hand work.

Name:  IMG_20200901_164955.jpg
Views: 553
Size:  55.9 KB
__________________
Eugene
Reply With Quote
  #13  
Old 09-01-2020, 10:36 PM
Reno Reno is offline
MetalShaper of the Month May 2020
 
Join Date: Nov 2018
Location: Reno, NV
Posts: 141
Default

The passenger side was the worst damage. I used the hinge locater again and metalworked the crease on the right. It was pretty well pitted, but I probably could have gotten by with a single vertical joint between the two original skins if I had thought that far ahead.


Name:  IMG_20200830_141850.jpg
Views: 546
Size:  41.2 KB


Name:  IMG_20200831_174200.jpg
Views: 546
Size:  48.0 KB

I sectioned the rear corner and will see if I can shape the rear half of the skin from new material to give an acceptable match tomorrow.

Name:  IMG_20200901_165115.jpg
Views: 541
Size:  50.7 KB
__________________
Eugene
Reply With Quote
  #14  
Old 09-03-2020, 08:49 PM
Reno Reno is offline
MetalShaper of the Month May 2020
 
Join Date: Nov 2018
Location: Reno, NV
Posts: 141
Default

I shaped a skin patch to complete the passenger side and then removed the old remaining section. It was too wide for my slip rolls, so I bent it over an old rim.


Name:  IMG_20200903_134837.jpg
Views: 488
Size:  58.3 KB

With the hinge bolt locator in place I scribed and trimmed.

Name:  IMG_20200903_142700.jpg
Views: 486
Size:  59.5 KB

I worked slower on this weld and ended up with less distortion.

Name:  IMG_20200903_174308.jpg
Views: 486
Size:  49.6 KB


Name:  IMG_20200903_174515.jpg
Views: 483
Size:  40.5 KB
__________________
Eugene
Reply With Quote
  #15  
Old 09-08-2020, 12:27 AM
Antoine_P Antoine_P is offline
MetalShaper of the Month August 2020
 
Join Date: Feb 2019
Location: Stuttgart, Germany
Posts: 113
Default

Great progress, thanks for sharing!

Antoine
__________________
Antoine Puygranier
Resurrecting a 60 ghia:
http://www.allmetalshaping.com/showthread.php?t=18852
Reply With Quote
  #16  
Old 09-09-2020, 09:54 AM
racer-john's Avatar
racer-john racer-john is offline
Member
 
Join Date: Mar 2010
Location: Shop is NO LONGER in "Asnorveldt"( the "Marsh"), Ontario, Canada
Posts: 268
Default 1950 Austin Devon

Any details on the "Bug"?
__________________
John S. E

_________________________________________________
Torque is nothing, unless you can get it to the road.
Reply With Quote
  #17  
Old 09-11-2020, 10:02 PM
Reno Reno is offline
MetalShaper of the Month May 2020
 
Join Date: Nov 2018
Location: Reno, NV
Posts: 141
Default

John, it was a Craigslist find I picked up in a weak moment because it is a 1962 so smog exempt here. It was a California car, but had the typical rusted floor pans. I replaced them and the driverside A post and found a 1972 1500 engine to power it.
Then I found the Austin.
__________________
Eugene
Reply With Quote
  #18  
Old 09-27-2020, 10:34 PM
Reno Reno is offline
MetalShaper of the Month May 2020
 
Join Date: Nov 2018
Location: Reno, NV
Posts: 141
Default

I hung the Dorset doors and the one with the most damage came out the best. Rookie mistake. I should have cut the B post out and tacked the door together in place. Anyway I had to cut the driverside door apart and change some dimensions. Then I found that there is so much damage in the rocker that needs to be replaced where the new B post position will be that I spent the day mounting the body on the rotisserie.


Name:  IMG_20200917_172136.jpg
Views: 154
Size:  43.6 KB
.
Name:  IMG_20200919_143533.jpg
Views: 154
Size:  38.2 KB

Name:  IMG_20200927_174253.jpg
Views: 154
Size:  71.1 KB

Name:  IMG_20200927_175101.jpg
Views: 154
Size:  60.4 KB
__________________
Eugene
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

All times are GMT -5. The time now is 12:59 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.