Peter Tommasini US MetalShapingClasses

[VetteMemphis]

Originally Posted by Cpeterson

Kerry,

Sent you PM with Nashville contact details



Craig

Craig, I'm very interested in the Nashville event.

What do I need to do? Did I miss something in an earlier post?

Thanks,

[Cpeterson]

Bruce,

Theres a email contact for Nashville up to the top of this thread, you can also call Rose at Street Rods by Michael ph: 931-680-0010 she can also walk you through registration process.

Craig

[tingeezer]

I would like to get on the list for Ft Collins, should I contact Bob Adame also? thanks, John

[Cpeterson]

Bobs email is at the top ot the thread, ok to contact him direct to register.

Craig

[red baron]

I received an email from another member and I would like to add here that if your on the fence, but not sure because you don't think you know enough. ..... This class is PERFECT not only for beginners but the experienced metalshapers

Having attended his first US class, that had one guy that had barely picked up a hammer in his life, to another that had years of experience, everyone and I mean everyone gained from the class and no one was in anyway a hindrance to the class.

I would consider this a must go to class before going to any that have large equipment. He will show you that everything is possible with minimal tools, some insight, and a lot of patience and perseverance.

[Cpeterson]

Class cost:
The cost for the three day class will be $650; which will include lunches. The registration cost will be collected a couple of months before the class start date; check with the event host or they will contact you. The event host should be able to advise you on what tools and safety equipment to bring. All shop materials will be supplied. Any other questions, please contact the event host.


Craig

[Cpeterson]

April 25th update on those that have expressed an interest in the class and are on the list.

Portland, Oregon ..........................3
Vancouver BC, Canada ..................6
Seattle/Tacoma Washington ...........2
Detroit, Michigan ..........................7
Nashville, Tennessee .....................6
Fort Collins/Denver, Colorado ..........7
Riverside/Temecula, California .........4

Note:
Not all of the classes above will be the same size, it will depend on the shop size. So it’s possible that some of these shops could be almost full.

The above numbers just reflect those that have emailed to be included on the list. There are others that are pending. So if this is a class that you might be interested in attending, you should get your name on a list fairly soon. We will keep the list active for standbys, when the class is full in case of a cancellation. We will try to keep the list updated weekly.

Regards,

Craig

[Cpeterson]

April 28th update on those that have expressed an interest in the class and are on the list.

Portland, Oregon ..........................4
Vancouver BC, Canada ..................6
Seattle/Tacoma Washington ...........3
Detroit, Michigan ..........................Full
Nashville, Tennessee .....................6
Fort Collins/Denver, Colorado ..........7
Riverside/Temecula, California .........4

Note:
Not all of the classes above will be the same size, it will depend on the shop size. So it’s possible that some of these shops could be almost full.

The above numbers just reflect those that have emailed to be included on the list. There are others that are pending. So if this is a class that you might be interested in attending, you should get your name on a list fairly soon. We will keep the list active for standbys, when the class is full in case of a cancellation. We will try to keep the list updated weekly


The information above that we have from Street Rods By Michael in, Shelbyville TN was from last week. It’s possible that the class might be filled up very soon as there seems to be a lot of interest from that area.

Class cost:
The cost for the three day class will be $650; which could include lunches (check with host). The registration cost will be collected a couple of months before the class start date; check with the event host or they will contact you. The event host should be able to advise you on what tools and safety equipment to bring. All shop materials will be supplied. Any other questions, please contact the event host.


Regards,

Craig

[Cpeterson]

May 6th update on those that have expressed an interest in the class and are on the list.

Portland, Oregon ..........................4
Vancouver BC, Canada ..................6
Seattle/Tacoma Washington ...........3
Detroit, Michigan ..........................Full --- waiting list 2
Nashville, Tennessee .....................7
Fort Collins/Denver, Colorado ..........7
Riverside/Temecula, California .........4

Note:
Not all of the classes above will be the same size, it will depend on the shop size. So it’s possible that some of these shops could be almost full.

The above numbers just reflect those that have emailed to be included on the list. There are others that are pending. So if this is a class that you might be interested in attending, you should get your name on a list fairly soon. We will keep the list active for standbys, when the class is full in case of a cancellation. We will try to keep the list updated weekly.

Class cost:
The cost for the three day class will be $650; which could include lunches (check with host). The registration cost will be collected a couple of months before the class start date; check with the event host or they will contact you. The event host should be able to advise you on what tools and safety equipment to bring. All shop materials will be supplied. Any other questions, please contact the event host.


Regards,

Craig

[kurt penner]

Want to go to vancouver class, sent email to renatto. Anything else I need to do?