|
|
Thread Tools | Search this Thread | Display Modes |
#1
|
|||
|
|||
BAILEIGH 2012 contest 1939 ford running boards for a C.O.E.
Well its time for me to enter in the GREAT BAILEIGH 2012 CONTEST......
I will try to walk you through how i built these running boards, for a 1939 ford C.O.E.. But let me tell you i'm slow at typing and slower on the computer. Making a paper pattern from our mock up running board. jim 39 coe 145.jpg Just another shot of the same thing. jim 39 coe 146.jpg Trimming the paper for a rough fit. jim 39 coe 147.jpg After tracing the lines of the mock up running board this is what the paper will look like. jim 39 coe 148.jpg You can see the 90 degree bend line for the back of the running board and our measurements are written on the pattern. jim 39 coe 149.jpg Now were ready to lay it out on steel so we can cut our first blank. jim 39 coe 192.jpg Stay tuned there is more to come and if you have any questions feel free to ask.
__________________
Johnny |
#2
|
|||
|
|||
We put the paper pattern on the steel, hold it down with magnets, then trace the outline with a sharpie
jim 39 coe 197.jpg Next we trim it. Its easier to trim by hand if you do some rough cutting first, leaving about 1/4 off of your line to be trimmed by hand. jim 39 coe 200.jpg Next file the edges jim 39 coe 201.jpg This is a DAN SHADY special file... The best on the market......Thanks DAN jim 39 coe 203.jpg And this is what it looks like cut out. It is wise at this time to cut the blank for the other side at this point. jim 39 coe 204.jpg
__________________
Johnny |
#3
|
|||
|
|||
Ok, like I said computers are not my strong point. This was suppose to be the second post not the third. It can still be done as the third step you just have to allow for the hemmed edge pryor to cutting. I hemmed my edge that way I didn't have to allow for the extra measurement when putting the pattern on (if that makes sense to anybody).
Fit pattern to steel jim 39 coe 150.jpg Scribe 1/2" line for the first fold jim 39 coe 193.jpg Put it in the brake and fold it all the way up jim 39 coe 194.jpg Open the brake and insert the fold and then close the brake. This will make a nice hem. jim 39 coe 195.jpg This is what your hem will look like jim 39 coe 196.jpg Sorry about the confusion if any.
__________________
Johnny |
#4
|
||||
|
||||
No confusion for me, just want to see more!
__________________
Brad |
#5
|
|||
|
|||
No confusion at all!
go ahead...
__________________
Mario http://www.speedlook.de |
#6
|
|||
|
|||
Ok this is where were at with the running boards cut out and the hem done.
jim 39 coe 205.jpg jim 39 coe 206.jpg One needs to pay attention when you do the hem so you dont wind up with two of the same side. ( In this case I now have two for the drivers side, but we just cut one more blank out and put the hem on the correct side so i now have one for the pass side.) jim 39 coe 208.jpg This is the home made radius brake that we made. jim 39 coe 211.jpg jim 39 coe 212.jpg Insert the running board blank in between the pipe jim 39 coe 213.jpg It some times needs a little taping. You will want to use a slapper when doing this, so you dont take a chance of dinging the edge This slapper is a door prize that I recieved from Rick Tucker and works great for the job. jim 39 coe 215.jpg
__________________
Johnny |
#7
|
||||
|
||||
Uncle Johnny, I may have missed this but what gauge steel are you using?
Looks good, keep the pics coming!
__________________
Robert Instagram @ mccartney_paint_and_custom McCartney Paint and Custom YouTube channel |
#8
|
|||
|
|||
I measured 2.5" from the pipe to the outside edge of the hem. The hem goes up so it will be on the inside of the running board
jim 39 coe 216.jpg Next you pull up on the handle and start to make the bend. jim 39 coe 217.jpg Bend it 90 deg. jim 39 coe 218.jpg It some times leaves the center a little less then 90 deg. so I taped it with the slapper to get it uniform. jim 39 coe 220.jpg Its now ready to take out of the break. jim 39 coe 224.jpg There you have it. jim 39 coe 225.jpg
__________________
Johnny |
#9
|
|||
|
|||
I'm using 19 because there is plenty of bracing under it.
__________________
Johnny |
#10
|
|||
|
|||
I wanted the beads to match the front running board. Minus the little bumps.
jim 39 coe 226.jpg So i put some tape on like this. jim 39 coe 227.jpg Put some marks on the center of the beads like this. jim 39 coe 228.jpg Then you can pull the tape off the front running board and put it on the new running board like this. jim 39 coe 229.jpg Then you mark the new running board like this. jim 39 coe 230.jpg Peel the tape off and you have your beads in the same place as the front running boards. jim 39 coe 231.jpg Then you realize you put the marks on the wrong side of the running board and you need to put them on the inside. So the beads stick out not in. jim 39 coe 232.jpg Dont forget to mark the running board jim 39 coe 233.jpg Then connect the dots so you have a visual on were the beads will go jim 39 coe 234.jpg Now your almost ready to make some noise. jim 39 coe 235.jpg
__________________
Johnny |
Thread Tools | Search this Thread |
Display Modes | |
|
|