All MetalShaping

Go Back   All MetalShaping > General Metal Shaping Discussion > Shop Safety
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-02-2019, 07:56 AM
Bart Bart is offline
Member
 
Join Date: Jun 2011
Location: Sydney, Austraila
Posts: 290
Default Transporting heavy machinery over lawn

Hi guys
I have a bit of an issue.
I need to move an old second hand CNC mill with a forklift to my back garage but I have a back yard/lawn. Its about 11 meters 36 feet from a concrete path to my back garage, back garage has a concrete floor.
Hiring steel road plates to lay on the lawn is around $2500 for a few days which is super expensive.
What other alternatives have people used other than road plates. I was thinking timber road plate, ply wood or similar used in construction which are pretty strong but don't know if they're strong enough. I don't mind if they get damaged as long as the forklift doesn't sink while carrying the CNC. The forklift and CNC together is about 10 tonn.
Any suggestions would be great
__________________
Bart Risuccia
Reply With Quote
  #2  
Old 06-02-2019, 09:21 AM
mr.c's Avatar
mr.c mr.c is offline
Member
 
Join Date: May 2009
Location: N. Florida
Posts: 698
Default

Hire a tilt-bed wrecker to move the machine or a dually tired forklift. I have two forklifts. One is a big dually tired and the other is warehouse type. The warehouse forklift is useless on anything but concrete or hard pavement. It is buried the moment it leaves a hard surface. I don't think that plywood would stand a chance.
I use the dually tired forklift all over my property. I have buried it a few times, however.
Put the machine on the wrecker with the forklift on hard ground. Slide it off into your shop. Then load your forklift onto the wrecker and move it back to the shop. Or put both on the wrecker and place the forklift into the shop first.
Trust me on this. Retrieving a buried forklift will not be the highlight of your day. It will be memorable however.
__________________
Carey Culpepper

TuckPuck® Metal Shaping Tools
www.tuckpuck.com
Reply With Quote
  #3  
Old 06-02-2019, 10:03 AM
Marc Bourget Marc Bourget is offline
Member
 
Join Date: May 2013
Location: North Ca
Posts: 716
Default

Having buried my hard tired forklift more than once, I support the suggestion.


The slideback should be less expensive than renting a rubber tired forklift.
__________________
Marc
Reply With Quote
  #4  
Old 06-02-2019, 10:26 AM
Stevemo Stevemo is offline
Member
 
Join Date: Jan 2017
Location: Ontario
Posts: 73
Default

A local construction company may have a loader with forks.
__________________
Steve
Reply With Quote
  #5  
Old 06-02-2019, 11:30 AM
blue62 blue62 is offline
Member
 
Join Date: Aug 2016
Location: Woodland Wa.
Posts: 315
Default

Do a internet search for swamp mats.
My experience with them has been positive.
They are light weight you can pick they up and move them by hand.
you can carry them in the back of a pickup truck.
they support heavy weight over soft condition.
I have used them on wet boggy grass and soil to move mini excavators, vactor trucks, dump trucks, dozers.
used them a lot in the work place. we always rented them. price was reasonable.
they should work well for your needs
__________________
Dave Bradbury
Reply With Quote
  #6  
Old 06-02-2019, 11:35 AM
Reno Reno is offline
MetalShaper of the Month May 2020. October 2023
 
Join Date: Nov 2018
Location: Reno, NV
Posts: 331
Default

I have used short lengths of 2" pipe as rollers to move heavy equipment. Theoretically it would only take three sheets of strong plywood, but a longer run speeds the process. One sheet under the machine and the others laid out as the track, or hopscotched across the lawn. The main concern is to control the momentum and direction so the machine stays on track. Also keep the center of gravity as low as possible to avoid tipping.
Good luck.
__________________
Eugene
Reply With Quote
  #7  
Old 06-02-2019, 01:31 PM
Jaroslav Jaroslav is offline
MetalShaper of the Month April 2020, September 2021, November 2022
 
Join Date: Dec 2012
Location: Czech Republic
Posts: 2,601
Default

Send photo machines and its bases. For idea.
It is possible to use 4 boards and move the machine on rollers or pipes or special moving bogies. When the board ends, you give another. 4 planks should be enough across the field. If it is uphill, you can use a winch or something similar to secure. If this is the case you can move the machine to all sides. If the machine is made of steel, it can be handled as it is. If the machine is made of concrete, you must use moving bogies.
The big crane won't reach there? Or are you just transporting on your land?

Dsc02768.jpg

DSC07508.jpg
__________________
Jaroslav

Last edited by Jaroslav; 06-02-2019 at 01:40 PM.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 03:39 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.