#1
|
|||
|
|||
One way to build a wood crate buck
I just completed the drawings for this Model A fender buck, and am posting while it is all fresh in my mind. This is not the only way, just one way. I like making drawings, so this is the approach that I have taken, and from my limited experience, I like the fact that I can use it as a hammer form buck if I need to. In some previous bucks, I was too liberal in making the buck ribs be vertical, leaving too much sanding to fit the actual contours. That also made it harder to hold up under some of the 'angled' hammer blows. I learned the West System glue usage from Jim Hery and the 3D scanning was done by Scott White at the last Redneck Roundup.
This the .IGES file that was sent to me by Scott White after he 'worked over' the point cloud from the 3D scan taken in the shop. MA1.jpg I saved that file as a parts file in SolidWorks. MA2.jpg One of the earliest steps was to establish a base and back bone that could be cut out of the available 60" x 60" Baltic birch plywood. Then a 'plane' surface was determined at the highest point of the contour and using the cut surface of the 3D scan the back bone was drawn to match that contour, and the cross web locations were cut in place. MA3.jpg By establishing a working plane at one side of the web slots, and using the edge of the fender as determined by the cutting plane, a cross web contour was established then extruded to the thickness of the plywood. By using the 'convert entities / intersection curve' command the dark line along the contour is established at the exact location of the fender skin. MA4.jpg This is the combination support and contour web from the above cross section. MA5.jpg Pre-assembly holes were added to the SolidWorks drawing of the base to locate the support webs and the component assembly was started. MA6.jpg One of the last cross ribs about to be inserted on to the back bone. MA7.jpg Pre- assembly of the drawing components almost completed. MA8.jpg Components in place. The notches at the side are for the edge ribbing. Where the edging looks to be protruding shows where the edging will be bent to the fender contour at the assembly gluing process. MA9.jpg Individual drawings are then made and further saved as a .dxf file for use at the water jet place. Minimal dimensions are required only to allow the water jet operator to check the scale before cutting. MA10.jpg For these larger projects, I assemble the components into a 60" x 60" plywood panel for cutting at the same time. MA11.jpg This is the drawing, in .dxf format that will be sent to the water jet guy for cutting. In both the above and below photos there are components that are for a Bugatti headlight buck project, as I could take advantage of combining projects. MA12.jpg Here is a picture of the completed buck without the fender in place. MA13.jpg This picture shows the fender superimposed on the buck. The parts that show above the fender scan are the areas that will need to be 'custom' sanded before being able to use the buck. The red outer edging component is made longer than the fender to account for the material needed to include the wire edging prior to forming the fender edge bead typical of the Model A's. MA14.jpg
__________________
Will Last edited by RockHillWill; 11-27-2016 at 01:46 PM. |
#2
|
|||
|
|||
Quote:
How did you determine the eye/hand openings, from making a fender or two?
__________________
Kent http://www.tinmantech.com "All it takes is a little practical experience to blow the he!! out of a perfectly good theory." --- Lloyd Rosenquist, charter member AWS, 1919. |
#3
|
|||
|
|||
Thanks, Kent. I do not have enough experience to decide in advance what I will need, just that I have observed that I need a number of openings to see as many place as I can to see how things fit. I also use pieces of metal pallet banding, some times bent to 'feel' in behind the panel. I'm still a little new to this, but getting 'boned up' for more work on Jim's Bugatti project.
__________________
Will Last edited by RockHillWill; 11-28-2016 at 07:20 PM. |
#4
|
|||
|
|||
Very, very nice work Will!
__________________
Bob Don't believe everything you think. |
#5
|
|||
|
|||
This is really fantastic, and makes me wonder about the degree to which this process could be completely automated -- you just push a button and a fender buck 3D puzzle arrives in the mail. Seems like you're about 70% there, already the labor savings is pretty staggering.
Does the water jet cutter only cut straight down or can it make bevel cuts in the plywood?
__________________
Joe |
#6
|
|||
|
|||
Joe, that water gent fellows that I use only have the three axis machines, but there are others that have extended capabilities.
__________________
Will |
#7
|
|||
|
|||
It will be a nice Buck Will !!
Peter
__________________
P.Tommasini Metalshaping tools and dvds www.handbuilt.net.au Metalshaping clip on youtube http://www.youtube.com/watch?v=WEAh91hodPg Making Monaro Quarter panel: http://www.youtube.com/watch?v=KIpOhz0uGRM |
#8
|
|||
|
|||
Will, you build the nicest bucks!
__________________
Mike |
#9
|
||||
|
||||
Nice work Will, I admire your ability of mastering SolidWorks and the way you explain in detail what the process is about. Thanks for posting.
__________________
Tom Poulter Follow the Dream - Sideways - - But don't fall-off the edge 'good to know you guys care' https://ctrestorations.com/ |
#10
|
|||
|
|||
Looks really great, Will.
I had wondered about angling station elements to better meet the actual part contours. It just makes sense. Thanks for sharing so much information.
__________________
AC Button II http://CarolinaSculptureStudio.com https://www.youtube.com/channel/UCzSYaYdis55gE-vqifzjA6A Carolina Sculpture Studio Channel |
Thread Tools | Search this Thread |
Display Modes | |
|
|