All MetalShaping

Go Back   All MetalShaping > General Metal Shaping Discussion > Shop Safety
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 09-09-2013, 06:22 PM
63galaxie 63galaxie is offline
Member
 
Join Date: Dec 2011
Location: Lodi , Ca
Posts: 22
Default Slow down take a deep breath and think before using machinery.

Just a reminder that sometimes we need to slow down and think about what we are doing. Yesterday morning I went to round over a piece of 1/4 plate for a chasing tool on my 20" disc sander. I put the plate into the disc at a bad angle and it pulled the plate and my thumb right between the table and the disc. I was able to yank my thumb out but not before it took about half the length on the top down to bone. I quickly wrapped it up and drove to the e.r. . 12 hours later they performed surgery to save what they could . I haven't seen it yet but I guess there is about a half inch left past the knuckle luckily. I have pictures but i don't think anyone really wants to see them Haha!
__________________
James Kahler
Reply With Quote
  #2  
Old 09-09-2013, 06:27 PM
Kerry Pinkerton's Avatar
Kerry Pinkerton Kerry Pinkerton is offline
Administrator
 
Join Date: May 2009
Location: Near Huntsville, Alabama. Just south of the Tennessee line off I65
Posts: 8,321
Default

Big disk grinders may be the most dangerous tool in the shop. Belt grinders/sanders in general for that matter. Gene Newcome, the guy who made the early Eastwood Ewheels, hosted a meet once and told me that he had more workman comp claims on their 20" disk grinder than everything else combined and they had a shop full of old old old punch presses with absolutely no shields or safety gear.

Sorry about your injury and hope you heal soon. It could have been much worse.
__________________
Kerry Pinkerton
Reply With Quote
  #3  
Old 09-09-2013, 06:59 PM
weldtoride weldtoride is offline
Member
 
Join Date: May 2009
Location: Northern Illinois
Posts: 896
Default

Your reminder is well-taken, James. Best wishes for a speedy recovery.
__________________
Mark from Illinois
Reply With Quote
  #4  
Old 09-09-2013, 10:56 PM
Doug M Doug M is offline
Member
 
Join Date: May 2012
Location: Portland Oregon
Posts: 266
Default

I'm sorry you got the reminder.

Note: wire brushes are bad things to have bite you also and they JUMP when at the edge of a metal panel.
__________________
Doug
Reply With Quote
  #5  
Old 09-10-2013, 12:32 AM
ByronR ByronR is offline
Member
 
Join Date: May 2009
Location: Aberdeen WA
Posts: 89
Default

I feel for ya James. Small goofs can have huge consequences. Two other issues come to mind. .
The day I retired (2005) I was installing florescent fixtures in my garage/workshop. Reached a little too far, fell maybe 2.5 ft onto concrete floor. Broke my right wrist and right ankle. When I was finally able to breath, I realized I was going to have to drive myself to help. Only good thing to come out of that.... my daughter got me a cell phone.

Ladders and solo work. Be cautious.
Wishes for a quick and successful recovery.
__________________
Byron

Invention is the mother of necessity.

Last edited by ByronR; 09-10-2013 at 12:34 AM.
Reply With Quote
  #6  
Old 09-10-2013, 10:30 AM
Dougg Dougg is offline
Member
 
Join Date: May 2009
Location: Michigan
Posts: 107
Default

The round disc sander is either a tool you love or hate. Most belt sanders are a combo of belt and disc. Myself I seem to hate the disc sander and will allways use the belt sander. At work the disc is allways tore up from something bad that happened. The same thing you described can easiely happen on a belt sander, but I still prefer a belt. I removed the disc from my combo in my shop. It is a power tool just like any other that you have to respect. If you don't, it will teach you a lesson you will never forget.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 12:53 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.