All MetalShaping

Go Back   All MetalShaping > Metal Shaping Projects > Automotive Projects
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 03-22-2020, 11:52 AM
MP&C's Avatar
MP&C MP&C is offline
MetalShaper of the month Feb.-11, July - 2018, Sept. 2020
 
Join Date: Mar 2010
Location: Leonardtown, MD
Posts: 1,707
Default Ford F7 Hood damage repairs

The owner of the Biederman truck we had done all those rust repairs and fabrications on also has a 51 Ford F7 with a Rollback body.





He was driving it down the road a few months back when the Delco Remy voltage regulator on the firewall malfunctioned and resulted in an electrical fire. The heat caused some of the filler on the outside of the hood above the fire to delaminate, showing up as circles in the paint. As we sanded these defects out it was noticed that an abundance of filler (+1/4") had been used. The more we looked, the more filler we found all over the hood. In an effort to yield some weight savings, the entire outside of the hood was stripped..






In order to have free access for planishing out the Atlantic Ocean defects, the hood brace was removed from the inside...








This revealed more defects that the last shop saw as fixes, but they won't leave my shop like that....

Rather than butt weld in the proper thickness metal, a piece of about 16 gauge is slipped behind the rust hole area (from dirt accumulating between brace and hood skin) and MIG welded around the perimeter. I think we can improve on that..








In addition to that, the brace had lost it's structural integrity, so we will remake the ends..








To start our repairs, a body sweep is used to capture the lower flange profile. Note that a profile cut out of construction paper/cardboard works as well.





Verifying the panel thickness. Despite this being an early 50's truck, despite this being a BIG truck, yes, the outer sheet metal here is STILL only 19 gauge.





The affected area was cut out using an air body saw, use what you have available. Note we have no corners in the cut to help improve consistency in weld shrinkage on either side.





The flange bend line is traced from our profile template/body sweep, and bent using tipping wheel on the bead roller (since it's not a straight bend). Here test fitted to the hood..





An Ice Pick (something everyone should have if doing this type of work) is used to mark the area of the cut and more importantly, the cuts for the flanges.





Next we trim the panel on the band saw leaving 1/4" extra around our marks. Next, we use offset snips and trim the flanges to the lines scribed. And ONLY the flanges.. Then the panel is re-fitted with the flanges flush with the original, and RE-scribe the round line, this time with more force to see the mark better.

Note the scribe line has moved closer toward the flange as we located the panel correctly with flanges flush..





Fitted... panel should be as tight as you can get it to minimize any shrinking/pulling.





Flanges and outer surface are both aligned to the original first and I use TIG to tack on the exact corner on both ends to maintain this alignment.. Side note.... tacking only one end and working around to the other may shrink as you go, pulling other end down where it no longer aligns. So in this case, align both ends, tack both ends, and then progressively work your tacks side to side toward the bottom of the circle.





Note here the flange was left long on our replacement. Trying to weld it in place already trimmed to fit will invariably cause the edge to burn back, making it more difficult to weld this seam all the way to the edge. Leaving the flange on our patch long makes the outer part serve as a heat sink where this burn back effect is less of an issue. Once the welds are dressed, trim the excess using offset snips..


__________________
Robert

Instagram @ mccartney_paint_and_custom

McCartney Paint and Custom YouTube channel
Reply With Quote
  #2  
Old 03-22-2020, 11:57 AM
MP&C's Avatar
MP&C MP&C is offline
MetalShaper of the month Feb.-11, July - 2018, Sept. 2020
 
Join Date: Mar 2010
Location: Leonardtown, MD
Posts: 1,707
Default

More patches to go!


The TIG is used to fully weld the patches in place...


Front side:





Back side, full penetration on the weld..





The weld seams are then planished and dressed. Next, the front of the hood had a stress crack adjacent to one of the rubber bumpers. To stabilize the hood prior to cutting out this area, the brace is clamped back in place..





The damaged area is cut out, a "doubler" had been used toward the front to add strength to the area, so care is used to not cut that off..








A replacement patch is cut out, bends added, and tacked in place. A plug weld ties this in with the doubler..








All trimmed and welds dressed, the hood bumper hole is re-drilled in the new patch. Then we notice a bit of filler closer to the nose of the hood (arrow). Let's remove that while we're here to see what carnage lies in wait.





Gotta love this game of dominos..





The low area needs to be bumped up, and with little room for swinging hammers, a new tool is in order. Using the South Bend "milling machine" a die is made for the outer portion..





Using a pair of C-clamp vise grips (there goes another pair) the die we made will be welded to one side, the opposite is giving a bit of a trim to better fit in the confines of the slight gap available on the inside..








I missed the action shots, but the clamping of the vise grip is used to raise the low areas. Then dressed out for a much better "filler free" lower edge for the hood.





With Mike having completed the dies to duplicate the ribs in the hood brace we did a test run on a piece of 16 Ga cold rolled steel. First upper die addresses middle rib only, way to much drawing going on to expect this out of one set of dies...








Then top die is changed out for the remainder of the ribs...








A bit of fine tuning needed, but looks like this process will work to repair the rot in the bottom of the brace ends..
__________________
Robert

Instagram @ mccartney_paint_and_custom

McCartney Paint and Custom YouTube channel
Reply With Quote
  #3  
Old 03-23-2020, 02:56 AM
metal manny metal manny is offline
Member
 
Join Date: Aug 2011
Location: Johannesburg, South Africa
Posts: 509
Default

Lovely work there Robert. Your client must be delighted. Great write up and pics too - thanks a bunch.
__________________
Manny

Remember that the best of men, are only men at best.
Reply With Quote
  #4  
Old 03-23-2020, 10:37 PM
Payupv8 Payupv8 is offline
Member
 
Join Date: Oct 2013
Location: Santa Cruz, CA
Posts: 98
Default

Nice job! I always learn something from your post. One question did you put any shape in that patch before you trimmed it down to fit the hood?
__________________
Eric Crafton
Reply With Quote
  #5  
Old 03-24-2020, 07:51 AM
Steve Hamilton's Avatar
Steve Hamilton Steve Hamilton is offline
ADMINISTRATOR MetalShaper of the Month Dec. '09 & May '11
 
Join Date: May 2009
Location: Fond du Lac WI.
Posts: 2,405
Default

Hi Robert

Nice save on the hood!
The reciprocating machines sure come in handy for ribs and beads.

Thanks for sharing.

Steve
__________________
Steve Hamilton
Hamilton Classics
Auto Restoration & Metalshaping
Reply With Quote
  #6  
Old 03-25-2020, 12:45 AM
qkiss qkiss is offline
MetalShaper of the Month February 2020
 
Join Date: Apr 2015
Location: Fortuna California -- up north behind the redwood curtain
Posts: 191
Default

Thanks Good post. ---- What are the dies made out of for the pullmax type machine?
__________________
Steve Kioukis
Sometimes your mind is stretched out of shape by a new idea never to go back to its original form.
Reply With Quote
  #7  
Old 03-25-2020, 05:57 AM
MP&C's Avatar
MP&C MP&C is offline
MetalShaper of the month Feb.-11, July - 2018, Sept. 2020
 
Join Date: Mar 2010
Location: Leonardtown, MD
Posts: 1,707
Default

Thanks Guys!!

Steve, the die is made from a piece of Phoenolic that I have had for many years. Alas, it is about used up and the stuff is rather pricey so I may have to find a new material to use. The benefit is that is was so easy to cut on the band saw..
__________________
Robert

Instagram @ mccartney_paint_and_custom

McCartney Paint and Custom YouTube channel
Reply With Quote
  #8  
Old 03-25-2020, 02:30 PM
dwmh dwmh is offline
MetalShaper of the Month May 2018, July 2022
 
Join Date: Aug 2015
Location: Nr Oxford UK
Posts: 659
Default

Nice detail of how you did that Robert. Can't believe the crap repair that was hiding under the filler, hope it was someones DIY job, rather than a so called professional. Your repair looked great, thanks for showing.
__________________
David Hamer
Reply With Quote
  #9  
Old 03-25-2020, 04:39 PM
Fargoman Fargoman is offline
Member
 
Join Date: Aug 2019
Location: Sydney Australia
Posts: 68
Default

Be aware phenolic material is carcinogenic.
Reply With Quote
  #10  
Old 03-27-2020, 06:36 AM
MP&C's Avatar
MP&C MP&C is offline
MetalShaper of the month Feb.-11, July - 2018, Sept. 2020
 
Join Date: Mar 2010
Location: Leonardtown, MD
Posts: 1,707
Default

Thanks for the comments!


Now to fine tune our dies for the hood brace. Looking at our original profile template, the first upsweep (red arrow) and second upsweep (yellow arrow) are both nearly vertical as compared to the opposite side.





Our first test run shows the first upsweep spread too wide, not enough vertical...





Looking at the die that was made, a bit too much material was removed such that this vertical feature was lost...





So a new die was made for the top, this time out of aluminum. The phenolic is somewhat easy to cut out but does have challenges in making crisp bend details, so lets see if the aluminum helps out..

Next run, this time we'll do two panels in case they work... First pass to draw the metal into the center rib...





This is about 8 passes, each progressively deeper. The circle fixture to the right in the picture (white base) is used as a back stop to keep our rib centered.





This is about 9/16 of depth, so quite a bit of draw.. Next, the new top die is added and goes through the same 8 progressive passes.. Note in the next picture the vertical upsweeps are both nearly vertical. Success!











Matching up to the original, this looks like the right replacement.





video version:


https://www.youtube.com/watch?v=OQgVST8TYgE






.
__________________
Robert

Instagram @ mccartney_paint_and_custom

McCartney Paint and Custom YouTube channel
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

All times are GMT -5. The time now is 12:27 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.