All MetalShaping

Go Back   All MetalShaping > Search Forums
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: 32chevy
Forum: Buck Building 12-20-2016, 06:25 PM
Replies: 38
Views: 30,673
Posted By 32chevy
Will nice job! Do you know what 3D scanner...

Will nice job! Do you know what 3D scanner equipment Scott White used? Any particular reason you chose to have the buck cut with water jet, it can be cost prohibitive. You must have access to some...
Forum: Basic questions and answers 12-08-2016, 12:04 AM
Replies: 8
Views: 6,876
Posted By 32chevy
Andrew, I took my snips and cut a 6" long sliver...

Andrew, I took my snips and cut a 6" long sliver of the edge off of some clean scrap 3003-h14. I cut the slivers width as close as I could to the material thickness. I didn't have any aluminum filler...
Forum: Basic questions and answers 12-04-2016, 10:41 PM
Replies: 8
Views: 6,876
Posted By 32chevy
Kerry, Marty; I had to tuck in the same spots...

Kerry, Marty; I had to tuck in the same spots eventually there so much shape to this piece. Maybe I should have cut the f.s.p. Up in different sections. It started to look like a mini 1940's rear...
Forum: Basic questions and answers 12-04-2016, 09:42 AM
Replies: 8
Views: 6,876
Posted By 32chevy
If I anneal the edge thurally shouldnt I be able...

If I anneal the edge thurally shouldnt I be able to eliminate the compressive stress created on the edge from shrinking? the cracks are on the edge 1/4"-1/2" long
Forum: Basic questions and answers 12-03-2016, 08:01 PM
Replies: 8
Views: 6,876
Posted By 32chevy
Aluminum, cracks from work hardening it

Wanted to share one of my first projects. I have read through half of the basic q's and A's threads,

I'm making a rear pulley cover for my delta drillpress. I chose 16ga 3003-h14 aluminum. I used...
Forum: Basic questions and answers 02-27-2016, 08:26 PM
Replies: 6
Views: 4,625
Posted By 32chevy
Kent thanks for your reply. I don't have a power...

Kent thanks for your reply. I don't have a power hammer. I was looking to apply this over a sand bag with panel and hammer
Forum: Basic questions and answers 02-27-2016, 11:20 AM
Replies: 6
Views: 4,625
Posted By 32chevy
Shrink with hammer. Trap perimeter & work center into surrounding

Can an over stretch area of a panel be shrunk with a hammer and proper technique. I just built a shrink stump and it is highly effective but only useful on panels edges. I have had success with...
Forum: Basic questions and answers 09-15-2015, 06:40 PM
Replies: 10
Views: 6,501
Posted By 32chevy
Which oval is correct, the one perpendicular to...

Which oval is correct, the one perpendicular to the panels length or..

I wheeled the short panel prior by wheeling outside the center box covering the outer third of the panel more then the areas...
Forum: Basic questions and answers 09-15-2015, 09:17 AM
Replies: 10
Views: 6,501
Posted By 32chevy
Will that oval be drawn tangent to all edges of...

Will that oval be drawn tangent to all edges of my panel?
Forum: Basic questions and answers 09-15-2015, 05:16 AM
Replies: 10
Views: 6,501
Posted By 32chevy
The top section , is what I'm trying to wheel. ...

The top section , is what I'm trying to wheel.

34381
Forum: Basic questions and answers 09-14-2015, 01:26 PM
Replies: 10
Views: 6,501
Posted By 32chevy
English Wheel tracking, T coupe trunk

Can anyone explain how to wheel up the top panel on the trunk lid, the section that has reverse curve. Ron covell shows how to briefly, wheel a similiar "tulip" panel but without detail as to...
Forum: Basic questions and answers 07-30-2012, 08:41 PM
Replies: 1
Views: 2,895
Posted By 32chevy
Forming window lips/contours for Model T?

How would one reproduce the rear panel on a 1927 model T coupe? I have the panel, its quite rusty and I was curious as to how the area where the window sits is made.

I assume it is done using a...
Forum: Introductions 07-10-2012, 12:09 AM
Replies: 1
Views: 1,119
Posted By 32chevy
Ryan of CT

Im from CT, grew up with a passion for reviving cars. I like home built tools. I have a few projects
[COLOR=black] [ [/COLOR
1932 Chevy Specs:

Boxed Chassis, custom K member, custom removable...
Showing results 1 to 13 of 13

 
Forum Jump
All times are GMT -5. The time now is 07:08 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.