Forum: Welding Sheet Metal
12-08-2017, 11:49 AM
|
Replies: 56
Views: 25,614
|
Forum: General Discussion
10-26-2017, 08:38 PM
|
Replies: 1
Views: 2,087
|
Forum: Welding Sheet Metal
10-23-2017, 07:31 PM
|
Replies: 17
Views: 10,034
|
Forum: Welding Sheet Metal
10-20-2017, 08:24 PM
|
Replies: 17
Views: 10,034
|
Forum: Welding Sheet Metal
10-20-2017, 11:37 AM
|
Replies: 17
Views: 10,034
Rivet alloys, shear strengths, and driving...
Rivet alloys, shear strengths, and driving condition[edit]
Alloy type Alphabetical letter Driven condition Marking on head
PLAIN
2117 AD 2117T3 DIMPLE
5056 B 5056H32 RAISED CROSS...
|
Forum: Automotive Projects
10-11-2017, 08:40 PM
|
Replies: 249
Views: 137,003
Howdy Kent,
Have you tried SharkHide on...
Howdy Kent,
Have you tried SharkHide on aluminum?
I have some ongoing trial swatches weathering, but I'd be curious if you have any experience with it.
Thanks for all your contributions to the...
|
Forum: Miscellanous products related to metalshaping
10-06-2017, 09:22 PM
|
Replies: 14
Views: 11,604
|
Forum: Miscellanous products related to metalshaping
10-03-2017, 10:00 PM
|
Replies: 15
Views: 11,967
My mistake, I thought you had a siphon...
My mistake, I thought you had a siphon setup.:dunce: I have a Haaba Fleight small box with the same issues that I had to tune up.
The crux is that you want 50% air and 50% sand, more or less. The...
|
Forum: Miscellanous products related to metalshaping
10-02-2017, 08:57 PM
|
Replies: 15
Views: 11,967
|
Forum: General Discussion
09-26-2017, 08:31 PM
|
Replies: 5
Views: 1,851
|
Forum: Basic questions and answers
08-09-2017, 09:03 PM
|
Replies: 23
Views: 8,098
If you do use a plaster cast, a thin film of...
If you do use a plaster cast, a thin film of Vaseline will provide the mold release.
Plaster of Paris and cheese cloth does a pretty good job of mold making. Burlap is a bit harder to saturate, but...
|
Forum: Introductions
06-27-2017, 08:00 PM
|
Replies: 9
Views: 2,948
|
Forum: Automotive Projects
06-09-2017, 11:28 AM
|
Replies: 147
Views: 88,768
I noticed that the exposed edging wire was...
I noticed that the exposed edging wire was rusted. Do you use any of the phosphoric acid conversion methods to treat the unexposed wire edging rust in situ? If so, do you have a favorite?
Thanks...
|
Forum: Tutorials
05-25-2017, 10:40 PM
|
Replies: 85
Views: 121,211
Did you "trap" the tuck first?
And there is a...
Did you "trap" the tuck first?
And there is a fine line between not enough, and too much, as regards the blows you give the metal. Caught between two metal faces, and too much force, you end up...
|
Forum: Basic questions and answers
05-06-2017, 08:05 PM
|
Replies: 35
Views: 11,535
|
Forum: Basic questions and answers
04-04-2017, 08:52 PM
|
Replies: 4
Views: 2,620
Did you weld on one side, and then the other? ...
Did you weld on one side, and then the other?
You might try going back and forth on the spot welds, and if that comes out straight, go back and infill the seam with weld, a little at a time, and...
|
Forum: General Discussion
04-04-2017, 08:45 PM
|
Replies: 4
Views: 3,852
|
Forum: Introductions
03-04-2017, 10:02 AM
|
Replies: 6
Views: 2,951
|
Forum: Automotive Projects
02-17-2017, 10:19 PM
|
Replies: 12
Views: 13,458
|
Forum: Basic questions and answers
02-07-2017, 10:26 PM
|
Replies: 20
Views: 6,970
|
Forum: Introductions
02-02-2017, 10:23 AM
|
Replies: 3
Views: 1,941
|
Forum: Automotive Projects
12-12-2016, 10:43 PM
|
Replies: 249
Views: 137,003
You might want to check continuity between the...
You might want to check continuity between the gauge hold down brackets and ground. It looks like they are setting on some paint. Might be a good idea to run a ground wire from both of them to a bare...
|
Forum: Introductions
12-07-2016, 09:16 PM
|
Replies: 4
Views: 2,869
|
Forum: Basic questions and answers
11-30-2016, 09:37 PM
|
Replies: 6
Views: 7,100
Her's a picture; ...
Her's a picture;
https://www.manualslib.com/manual/87424/King-Canada-52-Foot-Shear-Bb-F5216.html
It should be pretty self explanatory, if you look at it. The bow in the top blade is controlled by...
|
Forum: General Discussion
11-27-2016, 11:35 AM
|
Replies: 8
Views: 3,380
|