Forum: Automotive Projects
12-01-2020, 11:50 AM
|
Replies: 252
Views: 138,182
|
Forum: General Discussion
09-28-2020, 12:03 PM
|
Replies: 18
Views: 6,057
|
Forum: Metalshaping videos on-line
08-21-2019, 01:41 PM
|
Replies: 35
Views: 39,685
|
Forum: Welding Sheet Metal
04-28-2017, 03:44 PM
|
Replies: 19
Views: 7,211
Hi Kent, Looks like some deep scratches might...
Hi Kent, Looks like some deep scratches might indicate an attempt to clean the sample with abrasives rather than chemicals or stainless brush. If aluminum oxide paper was used some of the grit...
|
Forum: Welding Sheet Metal
11-29-2014, 03:49 PM
|
Replies: 41
Views: 156,373
|
Forum: Basic questions and answers
10-05-2014, 02:38 PM
|
Replies: 2
Views: 2,112
Hi Brett, I think you did a pretty good job of...
Hi Brett, I think you did a pretty good job of making, fitting and welding the patch. I think the grinding and finishing stages need a little more finesse. I think if you would only grind enough to...
|
Forum: Automotive Projects
05-31-2014, 09:26 AM
|
Replies: 252
Views: 138,182
|
Forum: Automotive Projects
04-20-2014, 06:20 PM
|
Replies: 252
Views: 138,182
|
Forum: Automotive Projects
04-19-2014, 10:57 AM
|
Replies: 252
Views: 138,182
|
Forum: Automotive Projects
04-17-2014, 04:59 PM
|
Replies: 252
Views: 138,182
Hi David, On page 4 you stated that a change of...
Hi David, On page 4 you stated that a change of flux has made welding brass more difficult than when you could use your favorite flux. Have you found a flux you like better yet? Today I oxy welded...
|
Forum: Posting Pictures
04-06-2014, 08:57 AM
|
Replies: 7
Views: 26,535
|
Forum: Welding Sheet Metal
03-06-2014, 03:55 PM
|
Replies: 27
Views: 12,162
|
Forum: Welding Sheet Metal
03-06-2014, 12:15 PM
|
Replies: 27
Views: 12,162
I have fuse welded aluminum with o/a with some...
I have fuse welded aluminum with o/a with some success. What I don't understand is the lack of back cracking when he is welding. As for the flux; I think he has a flux pot that delivers the flux...
|
Forum: General Discussion
12-19-2013, 09:37 AM
|
Replies: 3
Views: 2,422
|
Forum: Welding Sheet Metal
12-15-2013, 04:22 PM
|
Replies: 29
Views: 12,271
John, I will be eager to see what you find. I...
John, I will be eager to see what you find. I have been using most processes since 1970 (welding and fab school),but have not done any Oxy/Hydrogen or plasma torch welding, so maybe I can get some...
|
Forum: Welding Sheet Metal
12-15-2013, 12:28 PM
|
Replies: 29
Views: 12,271
Hey John, Is your interest in Oxy/Hydrogen...
Hey John, Is your interest in Oxy/Hydrogen welding in relation to welding aluminum? I was very interested in Oxy/Hydrogen until I got proficient with Oxy/Acetylene, then the advantages no longer...
|
Forum: Basic questions and answers
05-19-2013, 09:09 AM
|
Replies: 17
Views: 12,695
|
Forum: Welding Sheet Metal
05-03-2013, 09:48 AM
|
Replies: 13
Views: 9,215
Along with Christopher Rathman's warning about...
Along with Christopher Rathman's warning about using garden hose to supply breathing air, DO NOT under any circumstance breathe air from a compressor unless you are sure all contaminants have been...
|
Forum: Welding Sheet Metal
03-26-2013, 02:06 PM
|
Replies: 11
Views: 8,491
|
Forum: Basic questions and answers
12-04-2012, 12:35 PM
|
Replies: 25
Views: 16,120
|
Forum: Introductions
09-19-2012, 04:13 PM
|
Replies: 6
Views: 2,767
|
Forum: Basic questions and answers
08-14-2012, 03:13 PM
|
Replies: 8
Views: 6,903
|
Forum: Heads Up Announcements
04-16-2012, 09:13 AM
|
Replies: 17
Views: 13,686
|
Forum: Heads Up Announcements
04-13-2012, 08:55 PM
|
Replies: 17
Views: 13,686
|
Forum: General Discussion
01-14-2012, 11:06 AM
|
Replies: 12
Views: 23,706
|