Forum: Basic questions and answers
07-26-2014, 07:35 AM
|
Replies: 7
Views: 4,436
|
Forum: Basic questions and answers
07-26-2014, 07:18 AM
|
Replies: 4
Views: 2,368
|
Forum: Basic questions and answers
07-25-2014, 09:56 PM
|
Replies: 4
Views: 2,368
update on 32 Plymouth quarter panel
I have put some time in on trying to straighten out my quarter panel. I have made some progress. I still have a little bit of work to do, but it is much better. The straight edge laid over a little...
|
Forum: Basic questions and answers
07-23-2014, 09:31 PM
|
Replies: 12
Views: 8,292
|
Forum: Basic questions and answers
07-16-2014, 11:24 AM
|
Replies: 12
Views: 8,292
Thank you all for the input. The state of the...
Thank you all for the input. The state of the panel in the video is the result of quite a bit of work already done. Although a lot of that work was kind of like a person wandering lost in the...
|
Forum: Basic questions and answers
07-15-2014, 09:52 PM
|
Replies: 12
Views: 8,292
oil canning on the quarter panel
I have welded in the new lower section of my quarter panel. There was a lot of warping from sand balsting that was done to the car. After I welded in the panel, I started working on straighening it...
|
Forum: Basic questions and answers
07-11-2014, 10:00 PM
|
Replies: 4
Views: 2,876
Good Progress onthe quarter panels
With my rear fenders pretty much done, we tackled the quarter panels between the doors and rear fenders. I am pretty happy with them. I made a wooden form to shape them. My boy (going on 16) tried...
|
Forum: Basic questions and answers
07-07-2014, 10:21 PM
|
Replies: 2
Views: 2,265
Thanks for helping me be successful
My fenders for my 32 Plymouth are pretty much done. I got a coat of primer on them this weekend. I want to thank everyone for the valuable information that is shared here. I would not have been...
|
Forum: Basic questions and answers
06-18-2014, 11:09 AM
|
Replies: 2
Views: 2,399
another lead filing question
Can anyone give me a tip for keeping my file from clogging up with lead as I file. I am doing a lot of stopping to unclog the file.
Thanks,
Brad
|
Forum: Basic questions and answers
06-17-2014, 05:30 PM
|
Replies: 6
Views: 2,978
Lead Filing
I have made other recent posts regarding lead loading and have another question. If I am to only file the lead and not sand, then what are the right steps to get to a final finish. I have applied...
|
Forum: Basic questions and answers
06-16-2014, 12:20 PM
|
Replies: 3
Views: 2,425
|
Forum: Basic questions and answers
06-16-2014, 12:16 PM
|
Replies: 3
Views: 2,425
Sanding Lead and Cleanup
I am in the midst of my first attemp at lead loading. I am struggling, but making progress. I do have some questions.
I am doing a fair amount of a rear fender for a 32 Plymouth. Since you...
|
Forum: Basic questions and answers
05-27-2014, 10:33 PM
|
Replies: 7
Views: 4,323
coating metal before lead loading
I am restoring a 32 Plymouth PB that belonged to my dad in the 60's. I had it blasted last fall. I intended to prime it the moment that I got it back from the blaster. Instead, I have held off...
|
Forum: Welding Sheet Metal
05-15-2014, 11:40 AM
|
Replies: 2
Views: 3,012
32 Plymouth fender repair
I am moving along slowly with the repair on my LH rear fender for my 32 Plymouth. The more talented metal shapers on this site would have likely found it easier to fab a whole new fender. My...
|
Forum: Miscellanous products related to metalshaping
05-15-2014, 09:53 AM
|
Replies: 23
Views: 17,966
|
Forum: Basic questions and answers
04-21-2014, 11:55 AM
|
Replies: 11
Views: 5,420
wire edging
I need to repair some of the wire edging on the rear fender of my 32 Plymouth PB. Where do I get the wire? What size wire is typically used? I think what is in mine now is pretty small, maybe 16ga...
|
Forum: Events
03-07-2014, 10:51 AM
|
Replies: 10
Views: 5,708
I am interested. I am near Akron Ohio, so it...
I am interested. I am near Akron Ohio, so it will be a bit of a haul to get there. Please let me know what will be covered before I make a final decision to spend the time and money to come up...
|
Forum: Resources
02-26-2014, 12:41 PM
|
Replies: 40
Views: 48,930
|
Forum: Resources
02-25-2014, 04:47 PM
|
Replies: 40
Views: 48,930
David Gardiner DVD
I want to say that I am VERY new to metal shaping. I am neck deep in sheet metal replacement on my dad's 1932 Plymouth. I truly feel that the best tool investment that I have made so far on this...
|
Forum: Basic questions and answers
02-10-2014, 12:28 AM
|
Replies: 5
Views: 3,312
32 Plymouth rear corner
I am VERY new to metal shaping. I am restoring a 32 Plymouth PB. I will have many more questions after this one, but I am looking for some suggestions on how to form the rear corners. I have a...
|
Forum: Introductions
01-29-2014, 08:49 PM
|
Replies: 2
Views: 1,732
New Member from Copley Ohio
I am new to this group. I am neck deep in restoring a 32 Plymouth PB Coupe that was given to me by my dad. It was his daily driver from 63-67. When I was born he set it aside for me. It literally...
|