Forum: Basic questions and answers
01-22-2023, 01:03 PM
|
Replies: 24
Views: 5,623
You could also make a female mold from an...
You could also make a female mold from an existing clock face you have done. The reason I would make female as much easier to rework individual numbers or features on the mold.
These alloys...
|
Forum: General Discussion
02-28-2022, 04:43 PM
|
Replies: 13
Views: 4,216
I think you can use the forming radius as the...
I think you can use the forming radius as the only clamp also. And I would not want a bearing on the outside. Better to have some drag on the material when its pulled around the radius. You will...
|
Forum: Welding Sheet Metal
11-21-2021, 10:28 PM
|
Replies: 11
Views: 5,250
I use this on a Synchrowave 300. It cost less...
I use this on a Synchrowave 300. It cost less than some on off switches.
Uses several resistors and switches so that you get more amperage in steps with spring loaded paddle.
I would prefer the...
|
Forum: Basic questions and answers
11-11-2021, 10:44 PM
|
Replies: 9
Views: 2,632
|
Forum: Beginner Projects
10-26-2021, 11:08 PM
|
Replies: 53
Views: 26,294
While I think alcohol is safer than acetone...
While I think alcohol is safer than acetone either is safe for welding imo. Brake cleaner can turn to phosgene gas and I would never use it before welding.
Dont think acetone is a chlorinated...
|
Forum: Automotive Projects
01-20-2021, 02:04 PM
|
Replies: 40
Views: 123,097
I am widening and lengthening a Ford F1 truck....
I am widening and lengthening a Ford F1 truck. For the doors I drilled aluminum rulers #40 drill for clecos. That way I could match drill the door and slide the pieces 6" apart and re-attach 4...
|
Forum: Welding Sheet Metal
08-31-2020, 01:40 AM
|
Replies: 25
Views: 14,477
|
Forum: General Discussion
03-28-2020, 05:09 PM
|
Replies: 35
Views: 11,797
|
Forum: General Discussion
03-04-2020, 02:22 PM
|
Replies: 15
Views: 6,651
If you have a budget in mind that would help...
If you have a budget in mind that would help with suggestions. Also what tools do you currently own?
I prefer used name brands over new cheaper stuff if budget does not allow for new brands like...
|
Forum: Announcements
09-04-2019, 06:36 PM
|
Replies: 23
Views: 22,581
|
Forum: Welding Sheet Metal
08-22-2019, 01:02 AM
|
Replies: 11
Views: 14,034
|
Forum: Automotive Projects
03-21-2019, 11:15 PM
|
Replies: 463
Views: 252,914
|
Forum: Automotive Projects
03-11-2019, 10:14 PM
|
Replies: 2,001
Views: 3,170,364
|
Forum: Basic questions and answers
02-15-2019, 02:16 AM
|
Replies: 14
Views: 3,788
|
Forum: Basic questions and answers
02-14-2019, 09:44 PM
|
Replies: 14
Views: 3,788
|
Forum: Automotive Projects
02-10-2019, 12:50 PM
|
Replies: 25
Views: 7,821
|
Forum: Basic questions and answers
10-11-2018, 12:03 AM
|
Replies: 13
Views: 5,500
I needed to determine the aluminum alloy for a...
I needed to determine the aluminum alloy for a motorcycle subframe that I was doing several welds on last week. If 6061 it needed solution heat treating at 980°f. If 7005 I could age it with 320°f....
|
Forum: General Discussion
08-25-2018, 11:19 PM
|
Replies: 34
Views: 12,349
|
Forum: Basic questions and answers
08-20-2018, 01:47 PM
|
Replies: 37
Views: 12,130
Tax brackets dont work that way. Everyone pays...
Tax brackets dont work that way. Everyone pays the same on the lower earnings. If I make 50K and you make 100K then you pay the same on your first 50K as I do. Its a very common myth that jumping...
|
Forum: Shop Safety
07-17-2018, 01:39 PM
|
Replies: 18
Views: 26,800
|
Forum: Automotive Projects
07-01-2018, 10:48 AM
|
Replies: 147
Views: 88,867
|
Forum: Welding Sheet Metal
07-01-2018, 10:41 AM
|
Replies: 34
Views: 20,790
|
Forum: Miscellanous products related to metalshaping
02-11-2018, 10:23 PM
|
Replies: 6
Views: 8,971
|
Forum: Automotive Projects
02-06-2018, 06:59 PM
|
Replies: 34
Views: 12,499
|
Forum: Automotive Projects
02-06-2018, 05:22 PM
|
Replies: 34
Views: 12,499
|