Forum: General Discussion
11-25-2021, 09:37 AM
|
Replies: 10
Views: 3,172
|
Forum: Automotive Projects
02-08-2018, 11:37 PM
|
Replies: 34
Views: 12,499
It sounds like you are hiring a body man not a...
It sounds like you are hiring a body man not a metalshaper. A skilled guy working in an insurance driven shop is going to make good money. The dollar amount is dependent on where you live. I live...
|
Forum: General Discussion
10-12-2017, 09:35 AM
|
Replies: 11
Views: 4,673
|
Forum: General Discussion
08-03-2017, 10:52 PM
|
Replies: 4
Views: 2,791
|
Forum: Basic questions and answers
04-01-2017, 06:41 PM
|
Replies: 1
Views: 1,869
|
Forum: Events
03-30-2017, 01:10 PM
|
Replies: 11
Views: 6,729
|
Forum: Events
03-30-2017, 09:38 AM
|
Replies: 11
Views: 6,729
Thanks to host John and everyone who helped put...
Thanks to host John and everyone who helped put together this meet. Also big thanks to those who shared their knowledge freely with the attendees. This was my first Metalmeet and I look forward to...
|
Forum: Announcements
01-20-2017, 01:43 PM
|
Replies: 18
Views: 20,706
|
Forum: Miscellanous products related to metalshaping
01-04-2015, 12:55 PM
|
Replies: 12
Views: 13,632
|
Forum: General Discussion
01-21-2012, 06:51 PM
|
Replies: 29
Views: 9,628
Very generous again Shane. I know we all...
Very generous again Shane. I know we all appreciate what you do for the Metalshaping community through your products and sponsoring of tech contests which have brought out a lot of great ideas....
|
Forum: Heads Up Announcements
11-10-2011, 09:02 PM
|
Replies: 9
Views: 5,244
My bad, went back and found them covered. I...
My bad, went back and found them covered. I bought a couple sheets. The stack is still 4-5 inches thick, probably 60-70 sheets left. You might try Saturday, they have been having 15% off on...
|
Forum: Heads Up Announcements
11-04-2011, 09:48 PM
|
Replies: 9
Views: 5,244
|
Forum: Beginner Projects
02-25-2011, 09:01 PM
|
Replies: 14
Views: 7,733
|
Forum: Basic questions and answers
02-10-2011, 10:00 AM
|
Replies: 3
Views: 3,876
Whippet Radiator
I remember reading a thread on the HAMB about making an aluminum radiator. It may be of help. Is it going on a Whippet or a Speedster?
Andy
|
Forum: General Discussion
01-11-2011, 08:08 PM
|
Replies: 6
Views: 3,714
Keep trying, it can be frustrating at first. ...
Keep trying, it can be frustrating at first. Crush the tucks you have being careful not to fold them over. You can also stretch down into your bowl but that thin material may tear. You should try...
|
Forum: General Discussion
01-04-2011, 10:09 AM
|
Replies: 59
Views: 28,452
|
Forum: General Discussion
12-29-2010, 09:13 PM
|
Replies: 8
Views: 3,836
|
Forum: General Discussion
12-28-2010, 10:14 AM
|
Replies: 8
Views: 3,836
metalshaping contest entry
Here are the bowls pretty much finished. I managed to keep the diameter at 9" the second one is about 3/16" long and I may try a flange or step to connect them at some time. thank goodness for bad...
|
Forum: General Discussion
12-28-2010, 10:12 AM
|
Replies: 8
Views: 3,836
metalshaping contest entry
These pictures show after a round of stump shrinking and gradual progress. I had to tuck shrink from time to time to keep it round. Mostly just a lot of stretching and planishing to check progress....
|
Forum: General Discussion
12-28-2010, 10:06 AM
|
Replies: 8
Views: 3,836
Metalshaping contest entry
I finally got back to my contest project. My shoulder is still wacky so I had to cheat and use my hf planishing hammer to planish. I started out with 2 11" blanks of unknown aluminum .035 thick. I...
|
Forum: General Discussion
11-15-2010, 08:55 PM
|
Replies: 59
Views: 28,452
|
Forum: General Discussion
07-18-2010, 10:16 PM
|
Replies: 25
Views: 21,968
Do you need to move that much metal around the...
Do you need to move that much metal around the edge. You might only need 1/2 to 3/4 and it would be easier to control and shrink on the form.
Burning the soot off should anneal the metal well. Soot...
|
Forum: General Discussion
11-30-2009, 10:02 AM
|
Replies: 18
Views: 7,985
Tree ornament
Wow, Christophers post looks like he took pictures of my sunday morning, alas my welding was a failure and I need to try again. What thickness did you use on that ornament Christopher?
Andy
|
Forum: Introductions
10-27-2009, 09:14 AM
|
Replies: 8
Views: 3,509
|
Forum: Introductions
10-26-2009, 09:12 PM
|
Replies: 8
Views: 3,509
|