Forum: Automotive Projects
05-02-2016, 06:35 PM
|
Replies: 56
Views: 23,932
|
Forum: Automotive Projects
01-10-2016, 10:41 PM
|
Replies: 291
Views: 199,521
|
Forum: Automotive Projects
01-04-2016, 05:51 PM
|
Replies: 291
Views: 199,521
|
Forum: Automotive Projects
12-23-2015, 11:09 PM
|
Replies: 59
Views: 39,242
Nice work Robert, very impressive.
My...
Nice work Robert, very impressive.
My mother-in-law has a pickup painted National School Bus Yellow. Looks like it belongs to the school - duh.
Best regards and have a merry Christmas,
Dave.
|
Forum: Automotive Projects
12-14-2015, 10:18 AM
|
Replies: 59
Views: 39,242
|
Forum: Automotive Projects
12-12-2015, 12:17 PM
|
Replies: 59
Views: 39,242
Robert,
Under the assumption this was an...
Robert,
Under the assumption this was an insurance repair, did you initially bid to replace all those braces and outer panels or did you leave the inside open to hidden damage, do you estimate...
|
Forum: Automotive Projects
12-11-2015, 11:45 AM
|
Replies: 59
Views: 39,242
|
Forum: Miscellanous products related to metalshaping
09-10-2015, 04:10 PM
|
Replies: 13
Views: 16,639
|
Forum: Miscellanous products related to metalshaping
09-09-2015, 06:28 PM
|
Replies: 13
Views: 16,639
They are used by horseshoers to clinch the...
They are used by horseshoers to clinch the horseshoe nails in the hoof after reshoeing the horse. The nail is driven up through the shoe into the hoof and out the side of the hoof about an inch...
|
Forum: Automotive Projects
08-13-2015, 08:02 PM
|
Replies: 52
Views: 33,023
Kent,
I don't know a whole lot about...
Kent,
I don't know a whole lot about working aluminum so I will try to ask the question like it was steel instead. Hope you understand me.
When heat shrinking how do you know when it's "red...
|
Forum: Automotive Projects
02-13-2015, 04:27 PM
|
Replies: 2,248
Views: 4,371,859
I've found that by using the hammer in this...
I've found that by using the hammer in this manner it will loosen and/or break the handle inside the hammer's head (the place where the handle goes through the hammer head has a name but I can't...
|
Forum: Automotive Projects
02-09-2015, 06:51 PM
|
Replies: 2,248
Views: 4,371,859
|
Forum: Automotive Projects
10-15-2014, 03:35 PM
|
Replies: 12
Views: 11,159
|
Forum: Basic questions and answers
09-08-2014, 12:09 PM
|
Replies: 15
Views: 6,635
|
Forum: Automotive Projects
09-05-2014, 11:26 AM
|
Replies: 36
Views: 18,832
|
Forum: Basic questions and answers
03-10-2014, 06:18 PM
|
Replies: 30
Views: 15,112
|
Forum: Basic questions and answers
02-24-2014, 06:37 PM
|
Replies: 30
Views: 15,112
Beau,
Sounds like Gary made you a deal you...
Beau,
Sounds like Gary made you a deal you can't refuse.
If it was my hood first clean all the plastic filler out of those dents with a wire brush and drill. Make sure the back side is...
|
Forum: Basic questions and answers
02-24-2014, 06:13 PM
|
Replies: 23
Views: 10,591
|
Forum: Welding Sheet Metal
08-19-2013, 05:56 PM
|
Replies: 40
Views: 22,337
|
Forum: Basic questions and answers
07-12-2013, 12:52 PM
|
Replies: 14
Views: 5,824
If I was doing the job, I would remove the...
If I was doing the job, I would remove the reinforcement from the hood. Probably has a dozen spot welds that would need to be drilled. Then I would make the reinforcement fit the cowl because it...
|
Forum: Introductions
05-31-2013, 04:18 PM
|
Replies: 5
Views: 2,343
|
Forum: Automotive Projects
04-16-2013, 07:00 PM
|
Replies: 14
Views: 9,336
|
Forum: Basic questions and answers
04-15-2013, 06:40 PM
|
Replies: 24
Views: 14,828
My brother-in-law works for Lear-Jet in Tucson...
My brother-in-law works for Lear-Jet in Tucson and they have sales of stuff that gets dropped on the floor and then swept up. They don't climb down off the plane to pick something up unless it's an...
|
Forum: Automotive Projects
03-29-2013, 09:46 PM
|
Replies: 35
Views: 35,226
|
Forum: Beginner Projects
03-25-2013, 01:47 PM
|
Replies: 52
Views: 29,362
We see who's doing the block sanding in your...
We see who's doing the block sanding in your shop. I tried that once, didn't work out. She was Ok in the office with the books but out in the shop, too much of a distraction or if she made a...
|