All MetalShaping

Go Back   All MetalShaping > Search Forums
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Showing results 1 to 25 of 127
Search took 0.01 seconds.
Search: Posts Made By: jhery
Forum: Automotive Projects 05-11-2018, 11:16 PM
Replies: 14
Views: 1,576
Posted By jhery
Prototype 01 Engine and Body Framing

The engine used for this car is a Series 2 XKE which is almost identical in size with about a 100 more horsepower than the original Bugatti. The transmission fits perfectly and will make this an easy...
Forum: Automotive Projects 05-11-2018, 10:08 PM
Replies: 14
Views: 1,576
Posted By jhery
1935 Bugatti T57 Stelvio, Prototype 01 The frame

This is an endeavor which could not have been possible with out the help of Will Cronkrite and Scott White. Scott scanned the original car I was restoring from the frame up and sent all that data to...
Forum: Introductions 05-08-2018, 02:56 PM
Replies: 8
Views: 476
Posted By jhery
Welcome to the site. It was nice meeting and...

Welcome to the site. It was nice meeting and talking with you at Dan Pate's and keep up the good work in your new location.
Forum: Automotive Projects 04-22-2018, 08:05 PM
Replies: 123
Views: 38,280
Posted By jhery
Keep up the good work.

Keep up the good work.
Forum: Buck Building 04-22-2018, 08:01 PM
Replies: 23
Views: 2,900
Posted By jhery
Jag

Kyle you are doing a nice job.
Forum: Comments and Suggestions 03-29-2018, 10:43 PM
Replies: 25
Views: 3,873
Posted By jhery
Dan, I can pick it up for you on my way to...

Dan, I can pick it up for you on my way to Will's.:lol:
Forum: Automotive Projects 03-26-2018, 01:36 PM
Replies: 10
Views: 1,817
Posted By jhery
Scale difference

This is the rough modeling which shows the size difference between the two cars.

46283
Forum: Automotive Projects 03-26-2018, 01:23 PM
Replies: 10
Views: 1,817
Posted By jhery
1931 Bugatti T46 rebody to resemble Esders Roadster

Scott White, professor from University of PA, Computer Modeling School came to my shop this weekend to help me with a project I am starting later this year. We are removing the current body which...
Forum: Automotive Projects 03-01-2018, 10:45 PM
Replies: 47
Views: 9,320
Posted By jhery
Cowl vent

The cowl vent was fabricated out of brass and the gutter system is cast aluminum. It had two 1/4" countersunk screws holding it to the frame work. They dimpled the cowl vent on either end for the...
Forum: Automotive Projects 02-25-2018, 05:20 PM
Replies: 47
Views: 9,320
Posted By jhery
Fabrication and design of the sunroof

The sunroof was made out of white ash which is cut 3/4" thick. The pieces had to be cut with a crown in both directions so it required 8/4 wood blocks. The side pieces were cut first and screwed to...
Forum: Automotive Projects 02-24-2018, 10:46 AM
Replies: 47
Views: 9,320
Posted By jhery
Peter: The complete cowl section, A pillars into...

Peter: The complete cowl section, A pillars into complete roof and sunroof, both doglegs, both running boards, both spare tire wells, both sections around tire wheels and both rear side panels. It...
Forum: Automotive Projects 02-23-2018, 11:10 PM
Replies: 47
Views: 9,320
Posted By jhery
Header panel, cut in windshield, fit interior wood

The header panel was fabricated by making a contour pattern from another 35 RR in the shop with a sunroof. The shape and position are different for a fixed top and a sunroof arrangement. I lofted...
Forum: Automotive Projects 02-23-2018, 10:37 PM
Replies: 47
Views: 9,320
Posted By jhery
Tinbasher: I would be more surprised to find two...

Tinbasher: I would be more surprised to find two sides that matched. Coach- building is an art and not a science.

Gando: This car is being done for touring so he does not plan on showing it,...
Forum: Automotive Projects 02-21-2018, 11:21 PM
Replies: 47
Views: 9,320
Posted By jhery
Right side A pillar and bracing

I finishied out the left side A pillar, installed the rain-gutter on the left side, shaped the upper A pillar to fit the skin and fit cowl panel to square door openings. The temporary right side A...
Forum: Automotive Projects 02-19-2018, 10:12 PM
Replies: 47
Views: 9,320
Posted By jhery
Fabrication of the left A pillar and upper cowl

I started with the left A pillar since there was more of it there to imagine what it should look like. A couple of the photos show the right side was basically non existent so once I get the left...
Forum: Automotive Projects 02-19-2018, 09:51 PM
Replies: 47
Views: 9,320
Posted By jhery
Just Lookin, The boards are mostly flat sawn. The...

Just Lookin, The boards are mostly flat sawn. The wood is screwed together with Marine glue in the joints. The skins are either screwed or nailed on. They were just a carry over from the coach days....
Forum: Automotive Projects 02-19-2018, 09:44 PM
Replies: 19
Views: 2,414
Posted By jhery
technic to bend hinges

Norson, These photos show the way it is done. I did them on a magnetic brake and a 3/8 steel rod. I first used the brake to wrap around the rod and then I removed the hold-down piece of the brake and...
Forum: Automotive Projects 02-19-2018, 09:11 AM
Replies: 19
Views: 2,414
Posted By jhery
The streaking pattern is from the thin paper they...

The streaking pattern is from the thin paper they place between the sheets. It rained hard after I picked up the load of aluminum and the water ran between the sheets and dried that way but it sand...
Forum: Automotive Projects 02-18-2018, 11:08 AM
Replies: 47
Views: 9,320
Posted By jhery
Norson: You are correct about the blight and...

Norson: You are correct about the blight and disease. I am building a 29 Minerva and the sill plates for that are 8/4 x 12" x 82". That is one large piece of wood. White Oak is used for top bows...
Forum: Automotive Projects 02-18-2018, 11:00 AM
Replies: 47
Views: 9,320
Posted By jhery
Mark you are welcome to visit anytime. I...

Mark you are welcome to visit anytime. I probably have 200 hrs in the car so far and to build the body and metal 700 to 800 hrs. I am a one man operation so my shop is like a prison, I rarely...
Forum: Automotive Projects 02-18-2018, 10:49 AM
Replies: 47
Views: 9,320
Posted By jhery
Answers to Kerry

Kerry: I have been reconstructing and restoring Rolls Royce and Bentley cars for 44 years and have developed the mind of a British Coachbuilder. The British were very disciplined and conservative...
Forum: Automotive Projects 02-18-2018, 12:04 AM
Replies: 47
Views: 9,320
Posted By jhery
Framing the body

When the body was all taken apart or fell apart I started by building the main wooden framing which attaches the floor. The B pillars were carefully measured out from the firewall and cross...
Forum: Automotive Projects 02-17-2018, 11:00 PM
Replies: 19
Views: 2,414
Posted By jhery
Top panels for hood

The top panels are 54" long so I bought some 4x 10 sheets of aluminum and got 4 panels per sheet. My shear is 52" so it was a little tricky cutting them but by removing the fence and twisting them...
Forum: Automotive Projects 02-12-2018, 11:46 PM
Replies: 19
Views: 2,414
Posted By jhery
Drawings and waterjetting hinges

Will Cronkrite made drawings of the hinges and they will be cut out with the waterjet.45292

45293

45294

45295

45296
Forum: Automotive Projects 02-12-2018, 11:24 PM
Replies: 19
Views: 2,414
Posted By jhery
Close-up of dies and top panels

The press is powered by an electric over hydraulic pump from my old frame rack which can run 4 10 ton rams. It has a 5" stroke and has a manual release or automatic release. I use the automatic so...
Showing results 1 to 25 of 127

 
Forum Jump
All times are GMT -5. The time now is 06:37 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.